|
Who's Online
There currently are 5361 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
![](includes/templates/ZC03C00199/images/pixel_trans.gif) |
|
There are currently no product reviews.
![](includes/templates/template_default/images/stars_5.gif) ;
Great manual, great price. Has a few of the basic operating instructions that most service manuals leave out. Complete instructions for disassembling board by board, safety precautions, schematics, complete parts list.
![](includes/templates/template_default/images/stars_5.gif) ;
I am very pleased with the service manual for my RT-909. This was an easy purchase and great procuct, and much cheaper than other venues i had looked at. This web site is now listed in my favorites list. KEEP UP THE GOOD WORK. THANKS. J. BROWN
![](includes/templates/template_default/images/stars_5.gif) ;
A very well written and easy to understand manual.
![](includes/templates/template_default/images/stars_5.gif) ;
There was no problem at all.After paying i had to wait only a few hours,than i could
download the manual in best pdf-quality.
Thank You !
![](includes/templates/template_default/images/stars_4.gif) ;
I found this service manual to be complete in every detail except for troubleshooting charts. It would be helpful if it had a set of troubleshooting charts; however it is a very good manual otherwise and for the price it is very well worth it.
20/21V-L110M
SERVICE ADJUSTMENT
RF AGC Adjustment 1. Receive a good local channel. 2. Enter the service mode signal category and select the service adjustment "AGC". 3. Set the data value to point where no noise or beat appears. 4. Select another channel to confirm that no noise or beat appears.
CHROMA ADJUSTMENT
No. Adjusting point Adjusting procedure/conditions SUB-TINT (I2C 1 1. Receive the "Color Bar" signal through AV in. BUS CONTROL) 2. Connect the oscilloscope to TP47B (Pin (5) of P882) BLUE-OUT. Range : 10 V/div. (AC) (Use probe 10:1) Sweep time : 10 µsec/div. 3. Call the "SUB-TINT" mode in service mode. Adjust the "SUB-TINT" bus data to obtain the waveform shown as Fig 1. 4. "SUB-TINT" bus data decrease 4 steps to get final waveform. (Fig 2.) 5. Clear the SERVICE mode. Waveform and others
WAVEFORM 1
SAME LEVEL
W Y CY G MG R B
Fig 1
Fig 2
HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT
No. Adjusting point Adjusting procedure/conditions V-SLOPE (I2C 1 1. Receive the Monoscope Pattern Signal. BUS CONTROL) 2. Call the "V-LIN" mode. 3. Increase or decrease "V-LIN" by Volume key till the horizontal line in the center of monoscope is just at the position where the blanking starts. 2 V-CENTER (I2C 1. Call the "V-CENT" mode. BUS CONTROL) 2. Increase or decrease "V-CENT by Volume key till the picture is centered. Waveform and others
3 V-AMP (I2C 1. Call the "V-AMP" mode. BUS CONTROL) 2. Increase or decrease "V-AMP" by Volume key to set overscan to 10.0% typical. Adjustment Spec 10.0% range ± 1% 4 S-CORRECTION (I2C BUS CONFIXED DATA, NO NEED TO ADJUST. TROL) 5 H-CENTER 1. Call the "H-CENT" mode. 2. Increase or decrease "H-CENT" by Volume key to center the picture horizontal. 1. Receive the "Monoscope Pattern" signal. 2. Press the R/C to set Picture NORMAL condition.
6 Focus Adjustment
3. Adjust the focus control to get the best focus.
11
|
|
![](includes/templates/ZC03C00199/images/pixel_trans.gif) |
> |
|