|
|
|
Who's Online
There currently are 5947 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
;
This SM is quiet scarce and hard to find it is an excellent Service manual, very clear to read and to print schematics and diagrams, Hi quality, Complete manual with no pages missing. I am very pleased with the manual and the fast service I have received. Great place to shop.
Good luck finding you manual...
(3) (4)
(5)
Adjust the VP (vertical) and the HP (horizontal) position using the 4, buttons. Press the Memory Initialize key of the R/C to store the value in memory. If you do not have this key, short the pins of the 2 pin connector PI1 for one second, then remove. Select PIP mode and shift the sub-picture using the SHIFT button. Distance between PIP and edge of screen should be equal when shifted. if it is not, repeat (i)-(5). Surround Operation Check Adjustment Preparation Input the following audio signals to the audio input of the VIDEO INPUT terminals. When checking surround: L CH: 400Hz sine wave 475mVrms R CH: 5kHz sine wave 475mVrms Set the INT. SPEAKER : ON Set the volume controls of FRONT and REAR to center. Set the BASS, TREBLE and BALANCE to center. Note: Front waveform: Front speaker output of the set. Rear waveform: Rear speaker output of the set. Surround Off Check Set to SURROUND: OFF and check shown below is obtained.
2.5.3 Matrix Surround Check Adjustment Preparation (1) Set to SURROUND : MATRIX Check that the following waveforms are obtained. Front : Check that the phases of R and L are different and 400H.z is superimposed on 5kHz. The amplitudes of R and L are different. Rear : Check that the phases of R and L are opposite and 400Hz is superimposed on SkHz. Front Rear
2.5
O.Sms/div+
0.5ms/div+
2.5.1 (1)
that the waveform 2.5.4 Matrix Surround/Monaural Check Adjustment Preparation Check that the following waveforms are obtained. Front : R and L waveforms are almost equal. Rear : R and L waveforms are almost zero.
Front
@KHz)
Front
Rear
400Hz
(400Hz)
400Hz
OSms/div
Note: REAR output is no signal. 2.5.5 Hall Surround Check Adjustment Preparation (1) Set to SURROUND : HALL. Check that the following waveforms are obtained. Front : Check that the phases of R and L signals are different and 4OOHz is superimposed 5kHz. Rear : Check that the phases of R and L are opposite and 400Hz is superimposed 5kHz. The amplitudes of R and L are equal. Front Rear on
2.5.2 Surround Off/Monaural Check Adjustment Preparation Check that the following waveform is obtained. of 2 channels are equal.
The amplitudes
Front
400Hz
400Hz
Note:
Monaural check can be omitted. REAR output is no signal.
0.5ms/div-t
O.Eims/div+
Note:
Amplitude
levels
of front
R and L are not even.
18
|
|
|
> |
|
