|
|
|
Who's Online
There currently are 5840 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
;
Very fast and perfect delivery. Clear and well scanned. A lot of work professionally realized.
Again thak you a lot
 ;
This manual is accurate and of high quality. It is only volume 2 of the service manual. This is schematic, parts lists, and exploded mechanical drawings. The theory of operation and the diss-assembly instructions are in volume 1. The unit can be tricky to dis-assemble portions of so the volume 1 manual can be important. The product description of the manual is accurate but it does not say anything about volume 1 and the image of the front page does clearly say Volume 2.
NOTES: 1. Since the G light is very important for picture quality and performance, pay special attention in its adjustment. 2. Be careful not to touch the lens with your fingers when adjusting. (5) In case of R lens. Set the position where the chromatic aberration changes from red to crimson. As shown below, observe the vertical bright line and adjust lens focus where the crimson or red chromatic aberration slightly appears inside and crimson or red outside (reference value : 1~3mm) at the point specified in table below. Change the signal and fineadjust in the same way as the G lens. L
OPTICAL FOCUSING ADJUSTMENT BLUE
CHASSIS SCREEN SIZE L1 and L2 (PITCHES from CENTER) L1&L2 COLOR ABERRATION I 43GX10B/50GX10B 43� 50� 3.0 3.0 50DX10B/60DX10B 60� 50� 3.0 3.0
* * ** ** * * ** ** 2mm MAX 3mm MAX 3mm MAX 2mm MAX ** ** * *
(NOTE)
O 2mm MAX 3mm MAX 2mm MAX 2mm MAX * Slightly reddish or no color ** Slightly reddish or no color
Adjustment Procedure (7) After all colors have been adjusted, display all colors with the cross-hatch pattern signal and compare the focus (optical focus) performance with the limit sample set. (8) Then, select the circle pattern signal and compare the focus (optical focus) performance of each color and all colors together with the limit sample set. (9) If the focus performance is worse than the limit sample set, re-adjust step (1) to (6).
I
CHASSIS SCREEN SIZE L1 and L2 (PITCHES from CENTER) L1&L2 43GX10B/50GX10B 43� 50� 3.0 3.0
O
50DX10B/60DX10B 60� 50� 3.0 3.0
2.5 STATIC FOCUS ADJUSTMENT
Adjustment preparation (1) LENS FOCUS adjustment should be finished. (2) Contrast : MAX Brightness : Center. (3) Receive the circle pattern signal. (4) Apply covers to the lens of the colors you are not adjusting and project only one color on the screen. Adjustment procedure (1) Red and blue static focus adjustment. Adjust the static focus VR on Focus pack (UFPK) so that the center of circle pattern is the most clear. Check that the focus does not get conspicuously worse at the edges of the circle pattern signal or cross-hatch signal. (2) Green static focus adjustment. Adjust the static focus VR on Focus pack (UFPK) (for green) so that the center of circle pattern is the most clear. Check that the focus does not get conspicuously worse at the checking point, the periphery of circle pattern cross-hatch signal. NOTE: Checking point for the periphery of picture.
OPTICAL FOCUSING ADJUSTMENT RED
COLOR ABERRATION
(NOTE)
* * ** ** * * ** ** I 2mm MAX 3mm MAX 3mm MAX 3mm MAX ** ** * * O 2mm MAX 3mm MAX 3mm MAX 3mm MAX * Slightly reddish or no color ** Slightly reddish or no color
NOTE:
Setting the center between Red and crimson is optimum.
(6) In case of B lens. Set the position where the chromatic aberration changes from purple to green. As shown below, observe the vertical bright line and adjust lens focus where the purple or green chromatic aberration slightly appears inside and purple or green outside (reference value : 1~3mm) at the point specified in table below. Change the signal and fineadjust in the same way as the G lens. L
NOTE:
I O Setting to the center between purple and crimson is optimum. Checking point
28
|
|
|
> |
|
