|
|
|
Who's Online
There currently are 5648 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
D
Ausstattung des Arbeitsplatzes:
(Betriebspannung service 14,4 V)
GB
Work place equipment:
1. Netzgerät 15 V regelbar, 10 A
1. Power supply unit 15 volts adjustable, 10 A (Supply voltage service 14,4 V) 2. Signal generator (Meguro, Leader, Kenwood) 3. High impedance voltmeter Ri > 10 M� 4. Output meter; frequency counter; AF millivoltmeter; stereo encoder
2. Me�sender (z.B. Meguro, Leader, Kenwood) 3. Hochohmiges Voltmeter Ri > 10 M� 4. Outputmeter; Frequenzzähler; NF-Millivoltmeter; Stereocoder 5. Oszilloskop: - Empfindlichkeit: 5 mV bis 50 Volt/cm. - Bandbreite: Gleichspannung bis 50 MHz. 6. Tastköpfe 10:1 und 1:1 7. Schraubendreher / Abgleichstifte (keramisch) 8. Lötstation
5. Oscilloscope: - inp. sensitivity: 5 mV to 50 volts per division - bandwidth: d.c. to 50 MHz 6. Probes 10:1 and 1:1 7. Screwdriver / adjusting pins (ceramic) 8. Soldering station
Reparaturhinweise
Programmieren der Geräteparameter:
(ist nach Auswechseln von D860 / HF - Teil erforderlich) - FM ZF-Ablage - Suchlaufstoppschwellen FM - Programmierung der Stereo Schaltschwelle - RDS Schaltschwelle - Suchlaufstoppschwellen MW - Suchlaufstoppschwellen LW
Repair notes
Parameter programming:
(required after replacement of D860 / RF tuner) - FM IF offset - Seek tuning stop thresholds FM - Stereo threshold - RDS threshold - Seek tuning stop thresholds MW - Seek tuning stop thresholds LW
Servicemode
Servicemode aktivieren 1. Schalten Sie das Autoradio aus. 2. Betätigen Sie die Tasten 1 + 3 gleichzeitig und halten Sie die Tasten gedrückt. 3. Schalten Sie das Gerät ein und halten Sie die Tasten noch für ca. 1 Sekunde gedrückt.
Service mode
Activating the service mode 1. Switch the unit off. 2. Press the push-buttons 1 + 3 simultaneously and hold them depressed. 3. Switch the unit back on and hold on to the buttons for approximately one more second.
Nach diesem Schritt erscheint im Display für 2 Sekunden "SERVICE" und der manuelle Sender - Suchlauf ist unwirksam.
After this step the display will indicate "SERVICE" for 2 seconds and the manual tuning is inhibited.
Sie verlassen den Servicemode durch Ausschalten des Autoradios.
You can quit the service mode by switching the radio off.
-7-
|
|
|
> |
|
