|
|
|
Who's Online
There currently are 6004 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
 ;
Received downlink in less then 8 hours, Item was in good copy condition, and told me how to program the clock timer. The price was very resonable, and the process was very automated and was GREAT to work with.
;
Fast service, document is OK. Thanks! Searched for it long time.
;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
Mode
1. Press MODE until you see the indicator light glow for the desired setting. 2. Choose Cool, Dry or Fan. â� Coolâ��Cools the room. Press FAN SPEED to select High, Med, Low or Auto. Press the plus or minus TEMP button to adjust the temperature.
â�
Filter Monitor
1. When Filter Monitor indicator light is lit, remove, clean and replace the air filter. See �Cleaning the Air Filter.� 2. Press FILTER MONITOR after cleaning and replacing the air filter. This resets the filter monitor.
Dry�Dries the room. The air conditioner automatically selects the temperature. Fan runs on Low speed only. NOTE: Dry mode should not be used to cool the room. Fan�Only the fan runs. Press FAN SPEED to select High, Med or Low. The display shows the current room temperature. NOTE: Auto fan speed cannot be selected in Fan mode. NOTE: After 360 hours of fan operating time, the filter indicator light will turn on. It will remain on for 180 hours or until you press FILTER MONITOR. After 180 hours, it will turn off automatically.
â�
Temperature
â�
NOTE: After 5 seconds, display will show the current room temperature.
Press the plus TEMP button to raise the temperature. Each time you press or hold the plus TEMP button, the temperature will go up 2ºF (1ºC) until it reaches 90°F (32°C). NOTE: After 5 seconds, the display will show the current room temperature.
Fan Speed
NOTE: The Fan Speed button will operate only when the Cool or Fan mode has been selected. 1. Press FAN SPEED until you see the indicator light glow for the desired setting. 2. Choose High, Med, Low or Auto. â� Highâ��for maximum cooling
â� â� â�
Med�for normal cooling Low�for sleeping comfort Auto�automatically controls the fan speed depending on the current room temperature and temperature control setting NOTE: Auto fan speed cannot be selected in Fan mode.
â�
Press the minus TEMP button to lower the temperature. Each time you press or hold the minus TEMP button, the temperature will go down 2ºF (1ºC) until it reaches 64°F (18°C). NOTE: After 5 seconds, the display will show the current room temperature.
Timer Delay To set the Timer for a 30-minute to 24-hour delay until the air conditioner turns off (the air conditioner must be On):
1. Press TIMER. Timer indicator light will flash. Display will show remaining hours before the air conditioner will turn off. NOTE: After 5 seconds, the display will show the current room temperature.
2. Press the plus or minus TEMP button to change the delay time from 30 minutes to 24 hours. 3. After 5 seconds, Timer indicator light will remain on. Display will show the current room temperature.
10
|
|
|
> |
|
