|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
;
This is a great manual. It was easy to read and very accurate. The size of the manual is small so email is no problem. I highly recommend it. The manual is very hard to find other than this website.
Copying (continued)
3. Hold the [START] button for at least 2 seconds Copying begins, and the verification 1) is conducted (when the [VERIFY] switch is set to ON). The copying progress is indicated by the LEDs, as follows. : LED lit ,, : LED flashing G : green OR : orange
COPY STATUS Progress (%)
G G G G G G G G G G G G G G G G G G 4. Make sure all the [COPY STATUS] LEDs are lit in green 5. Press the [POWER] button Copying is complete and the [COPY STATUS] LEDs go out.
00-19 20-39 40-59 60-79 80-99 100
During access OR G G
During access OR
Note: � Once the data on a P2 card has been copied to the HDD, it cannot be copied to the HDD again. If this is the case, one of the following operations will be performed depending on the [VERIFY] switch setting. [VERIFY] switch is OFF: Even when step 3 is taken, 100% is immediately displayed as the copying progress status. [VERIFY] switch is ON: When step 3 has been taken, the data is not copied, 40-59% is displayed as the copying progress status, and the verification is conducted. � Even after data on a P2 card has been edited, added or deleted by a computer or other device, it may be recognized as the same data. If this is the case, one of the following operations will be performed depending on the [VERIFY] switch setting. [VERIFY] switch is OFF: Even when step 3 is taken, 100% is immediately displayed as the copying progress status. [VERIFY] switch is ON: When step 3 has been taken, the data is not copied, 40-59% is displayed as the copying progress status, the verification is conducted, the data is recognized as different, and operation ends with the Verify NG error 2). (See page E-31) � If the unit heats up during copying, it will automatically copy at a slower rate. The [P2C] and [HDD] LEDs also flash slowly at this time. � If copying is not completed normally (if the unit is turned OFF or the P2 card is pulled out during copying), the HDD capacity (number of cards that can be copied) is decreased by as many P2 cards that could not be copied. � All [COPY STATUS] LEDs flash in green if a blank P2 card is inserted and step 3 above is finished. � In the case of P2 cards that include a Bad clip 3), be sure to first restore any lost data using a P2 camerarecorder or other device before copying using this unit. When a defective clip is copied without correcting its defects, it may not be possible to repair the copied defective clip. 1) This function conducts the verify whether the data on P2 cards and the data recorded on the internal HDD are the same. 2) When the Verify NG error has occurred, �ERROR� appears in the status column of the HDD partition information section (see page E-23). If this is the case, the data on the P2 card concerned can be copied again, but the partition with the �ERROR� status will remain unchanged. 3) Improperly recorded clip due to accidental removal of the P2 card or sudden power loss during recording. Clips with a yellow X marker displayed on the thumbnail screen when using a P2 camera-recorder or similar device.
E-16
ENGLISH
|
|
|
> |
|
