|
|
|
Who's Online
There currently are 6017 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A great copy of the manual, and the only one I could find anywhere on the net! The circuit diagrams are easily readable, all component values marked and easy to see. A highly appreciated download!
 ;
Great Manual. This manual is available no where else. It was exactly what I was looking for.
;
The TEAC A-1500's Service Manual was instrumental in reviving this classic reel-to-reel. Not only does it have the schematics, exploded parts diagram and parts list, it also provided mechanical adjustment information that approximate factory default settings.
;
This service manual was determinant to enable to fix my Alpine Amplifier. I am pleased with my purchase. For a 5 star rating I would like to see a higher resolution scan of the printed circuit board lay-out because the gray scale grafics was dificult to see. Also some schematic diagrams were scanned at a slight angle. Never the less, it had all information I needed to troubleshoot and service my equipment.
;
Complete manual, the good quality of reproduction allows enlarged print-out of the schematic diagram in the size it probably had in the original print edition and which is necessary for practical use.
LC-28HM2
AN-28SP2
ADJUSTMENT PROCEDURES
When indicating the adjustment line in the process adjustment mode, it is described in such a manner that the second line on page 1, for example, is �P1L2�.
1. Precautions and notes for adjustment » As power source, use the stable AC power. » Note that, when the power is switched on for the first time, it takes approx. 10 seconds before the unit starts up because E2P needs to be initialized. (Both monitor side LED and AVC center side LED are lit in green, with the backlight being OFF.) Never turn off the power during this time. When restarting the system the first time after the power interruption caused by power failure, etc., execute P6L5 �CENT EEP RST S/C ONLY� for resetting before doing adjustment. » When the data has been updated in the program more than once, updating the program will not re-write the adjustment value in most cases. Any time the program has been updated, it is recommended to follow the procedure; (a) save the data of the adjusted items in memorandum, (b) initialize the EEPROM once at both AVC center and monitor, and then (c) write in the adjustment values recorded. 2. How to enter into special modes 1 Going into the process adjustment mode [Procedure] (1) Using remote controller Connect the display and the AVC center using the system cable in the specified manner. Switch on the power. After start-up, press [PROCESS ADJUSTMENT] button of the remote controller. (2) Using main unit key Connect the display and the AVC center using the system cable in the specified manner. While pressing [BRIGHTNESS] and [VOL�] buttons simultaneously, switch on the power. [Contents] Various adjustments can be made manually. 2 Going into the inspection process mode [Procedure] Go into the process adjustment. Turn P1L6 �SIGNAL INFO� to �ON�. Terminate the process adjustment mode with remote controller operation. [Contents] The bar display items such as volume and video/sound adjustments are made switching in the sequence of minimum, medium and maximum. 3 How to make presetting [Procedure] (1) When remote controller capable of outputting the �preset� code is not available Go into the process adjustment. Turn P27L1 �INDUSTRY INIT� to �ON�, and the press [ENTER] button of the remote controller. The process is finished when �/ / / / / / / / / / / / / / / / / / / / / / / / / / / / � display disappears. (2) When remote controller capable of outputting the �preset� code is available Go into the process adjustment. Press [PRESET] button of the remote controller. The process is finished when �INDUSTRY INIT NOW� display disappears. [Contents] User adjustment value can be made as default setting. The data adjusted in the process adjustment is not altered.
16
|
|
|
> |
|
