|
Who's Online
There currently are 5974 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
AV-21BF11ENS AV-21BF11EES AV-21BF11EPS AV-21BF11EJS
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Unplug the power c ord. 2. Remove the 6 screws marked A as shown in the Fig. 1. 3. Withdraw the rear cover toward you.
CHECKING THE PW BOARD
To check the back side of the PW Board. 1) Pull out the PW Board. (Refer to REMOVING THE MAIN PWB). 2) Erect the PW Board vertic ally so that you c an easily check the back side of the PW Board. [CAUTION] " When erecting the PW Board, be c areful so that there will be no contacting with other PW Board. " Before turning on power, make sure that the wire connector is properly connec ted. " When conducting a check with power supplied, be sure to c onfirm that the CRT EARTH WIRE (BRAIDED ASS�Y) is connected to the CRT SOCKET PW board.
REMOVING THE MAIN PWB
" Removing the rear cover. 1. Remove the screw marked B as s hown in the Fig.1. 2. Slightly raise the both sides of the chassis by hand and withdraw the MAIN PWB backward. (If necess ary, take off the wire clamp, connectors etc.)
REMOVING THE SPEAKER
" Removing the rear cover. 1. Remove the 2 screws marked C, and remove speaker as s hown in Fig. 1. 2. Remove the speaker.
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the c able tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new c able tie.
REMOVING THE FRONT AV & HEADPHONE PWB
" Removing the rear cover. " Removing the rear MAIN PWB. 1. Remove the 2 screws marked D. 2. Remove the FRONT AV & HEADPHONE PWB.
6
No.52055
|
|
|
> |
|