|
|
|
Who's Online
There currently are 5754 guests and
3 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
AV32P10EKS AV32P10EIS
REMOVING THE CRT
Replacement of the CRT should be performed by 2 or more persons. After removing the rear cover, chassis and anode wires etc. 1. Prepare the CRT change table, the CRT change table should also be covered with such soft cloth as shown in Fig.4. The CRT change table should preferably be smaller that the CRT 2. 3. 4. 5. surface, and its height be about 35cm. While keeping the CRT down surface, mount the TV set on the CRT change table as shown in Fig.4. Remove 4 screws marked by arrows with a box type screw driver as shown in Fig.5. Since the cabinet will drop when screws have been removed, be sure to support the cabinet with hands. After 4 screws have been removed, put the cabinet slowly on cloth. At this time, be carefully so as not to damage the front surface of the cabinet as shown in Fig.6. The CRT should be assembled according to the opposite sequence of its disintegrated steps. CRT CHANGE TABLE
APPROX. 35cm CLOTH
Fig. 4
6.
[About CRT Spacer] An appropriate CRT spacer should be used in the corresponding CRT in accordance with the type of the CRT. When a CRT is replaced, special attention should be paid to this matter.
Fig. 5
CRT
COATING OF SILICON GREASE FOR ELECTRICAL INSULATION ON THE CRT ANODE CAP SECTION.
Subsequent to replacement of the CRT and HV transformer or repair of the anode cap, etc. by dismounting them, be sure to coat silicon grease for electrical insulation as shown in Fig.7. Wipe around the anode button with clean and dry cloth. (Fig.7) Coat silicon grease on the section around the anode button. At this time, take care so that any silicon greases dose not stick to the anode button. (Fig.8) Silicon grease product No. KS - 650N
CABINET
CRT CHANGE TABLE
Fig. 6
CRT
Anode button
Approx. 20mm (Do not coat grease on this section
Silicon grease should be coated by 5mm or more from the outside diameter of anode cap.
Silicon grease coating
Anode button (No sticking of silicon grease)
Coating position of silicon grease Anode cap
Fig. 7
Fig. 8
10
No. 51829
|
|
|
> |
|
