|
|
|
Who's Online
There currently are 5246 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The service was quick and simple, finding the service manual easy and it appears to be the original with colour schematics. It contained the info I was after and so sorted the problem.
I have copied it to CD and attached the envelope to the inside back cover of the owners manual. Good manual and excelent service. Robin Wood, Wood Electronics, New Zealand.
;
Exactly what was needed to assess the product - excellent value and great service
 ;
Nice to have the service manual for the Sony DCR-TRV345E now. The document is of excellent quality.
;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
AV32X10EUS AV28X10EUS AV28X10EKS AV28X10EIS
REMOVING THE CRT
$ Replacement of the CRT should be performed by 2 or more persons. ! 1. 2. 3. After removing the cover, chassis etc., Putting the CRT change table on soft cloth, the CRT change table should also be covered with such soft cloth (shown in Fig.3). While keeping the surface of CRT down, mount the TV set on the CRT change table balanced will as shown in Fig.4. Remove 4 screws marked by arrows with a box type screw driver as shown in Fig.4. CRT CHANGE TABLE
APPROX. 35cm
CLOTH
! Since the cabinet will drop when screws have been removed, be sure to support the cabinet with hands. 4. After 4 screws have been removed, put the cabinet slowly on cloth (At this time, be carefully so as not to damage the front surface of the cabinet) shown in Fig.5. ! The CRT should be assembled according to the opposite sequence of its dismounting steps. $ The CRT change table should preferably be smaller that the CRT surface, and its height be about 35cm. (Fig.3) $ About CRT Spacer (Fig.4) An appropriate CRT spacer should be used in the corresponding CRT in accordance with the type of the CRT. When a CRT is replaced, special attention should be paid to this matter.
Fig. 3
Fig. 4
CRT
COATING OF SILICON GREASE FOR ELECTRICAL INSULATION ON THE CRT ANODE CAP SECTION.
! Subsequent to replacement of the CRT and HV transformer or repair of the anode cap, etc. by dismounting them, be sure to coat silicon grease for electrical insulation as shown in Fig.6. Wipe around the anode button with clean and dry cloth. (Fig.6) Coat silicon grease on the section around the anode button. At this time, take care so that any silicon greases dose not stick to the anode button. (Fig.7)
CABINET
CRT CHANGE TABLE
Fig. 5
� Silicon grease product No. KS - 650N CRT Anode button Approx. 20mm (Do not coat grease on this section Silicon grease should be coated by 5mm or more from the outside diameter of anode cap.
Silicon grease coating
Anode button (No sticking of silicon grease)
Coating position of silicon grease
Anode cap
Fig. 6
Fig. 7
10
No. 51780
|
|
|
> |
|
