WHIRLPOOL AWT 8125
Owner's Manual

3gb00029.fm5 Page 2 Tuesday, March 13, 2001 2:56 PM

CONSUMPTION DATA Temperature Selector Programme White Cotton Coloured cotton Coloured cotton Synthetics Synthetics Rapid Plus Delicates Silk Wool (°C) 95 60 40 60 40 30 40 30 40 (kg) 5.0 5.0 5.0 2.0 2.0 3.0 1.5 1.0 1.0 (l) 49** 48 48 54 50 35 50 35 50 (kWh) 1.60 0.95 0.60 0.70 0.50 0.40 0.50 0.40 0.50 Load Water Energy Approx. Programme Duration (hours : minutes)* 2:00 2:05 2:00 1:30 1:15 0:30 0:45 0:35 0:45

Note: The programme stops to �Rinse Hold� when the �Rinse Hold� light indicator programme is on during the cycle. Appliance in Rinse Hold � �: � Press the �Rinse Hold� button again: the programme will terminate automatically with the selected spin cycle. � If you do not wish to spin the clothes, turn the programme selector knob to the Drain � � programme and press the �Start/Pause� button again. Spin Speed Reduction � � button � Every programme has an automatically allocated maximum spin speed. � Press the button to set another spin speed. � If the spin speed �0� is selected, the final spin is cancelled, but not the intermediate spins. The programme ends with a drain cycle.

DOOR LOCK
For safety reasons, the door is locked during certain phases of the cycle. At the end of the cycle or during an interruption, the door unlocks automatically after about 1 minute. END OF WASH CYCLE � The remaining time is on �0: 00� and the �End� lamp lights up. 1. Turn the programme selector to the � � position. 2. Turn the tap off. 3. Open the door and the drum flaps and unload the machine.

CHANGE THE PROGRAMME OR OPTIONS DURING THE CYCLE
1. Select the new programme using the programme selector. If necessary, select the additional options and the spin speed. The luminous indicator of the �Start/Pause� button flashes. Note: the Start Delay � � and Prewash � � options cannot be selected after a programme change. 2. Press the �Start/Pause� button. The new programme selected continues at the same position where the previous programme was interrupted. Note: Do not add detergent for this programme.

START DELAY
The Start Delay � � button allows the user to run the machine at his convenience, for example at night when electricity is cheaper. � Select programme, temperature and options. � Press the �Start Delay� button several times to select the delay time by 1 to 19 hours; � Press the �Start/Pause� button. The indicator light of the �Start/Pause� button lights up and the lamp of the �Start Delay� button flashes. � The time delay indication disappears when the programme starts and is replaced by the remaining time. � The number of hours preselected can be reduced later by pressing the �Start Delay� button again. To cancel the �Start Delay� option � Turn the programme selector to the � position. � � Reselect the desired programme and options and press the �Start/Pause� button.

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized conditions in compliance with standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. The data on the �Energy Label� refer to the programme �Coloured Cotton 60°C�. * The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household conditions applicable at that time. **To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

PREPARATION OF WASH CYCLE
1. Close the drum flaps and check that they are properly locked. 2. Add detergents and additives into the dispenser to no more then the �MAX� level mark, as follows: � Programme with pre and main wash � Main wash programme without prewash � Fabric softeners and conditioners � Chlorine bleach � Stain remover agents � Ant-scale agents (if necessary) 3. Turn the programme selector knob to the desired programme. The remaining time display � � shows the duration of the chosen programme (in hours and minutes) and the indicator light of the Start/Pause � �button flashes. The programme sequence and the predefined spin speed indication corresponding to the selected programme lights up. The preselected temperature � � can be altered by pressing the �+� or �-� button.

SELECT THE DESIRED OPTION
When you select an option authorized by the programme, the corresponding indicator lights up, except if the combination of programme, additional options and temperature is not possible. In this case an audible signal sounds. Prewash � � button � Only for heavily soiled loads (for example sand, granular dirt). Intensive Rinse � � button � The amount of water is increased to ensure a more intensive rinse. � This option is particularly suitable for areas with very soft water, washing baby linen and people with skin allergies. Rinse Hold � � button � The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from fading. � This option is particularly recommended for the Synthetics � � or Delicates � � programmes. � This function is particularly useful if you want to postpone spinning to a later time, or if you want to drain only.

PAUSE/INTERRUPT A PROGRAMME
If, for any reason, you wish to interrupt the programme for a certain time and continue it later: 1. Press the �Start/Pause� button. The light flashes.

2. After the desired pause, press again on the �Start/Pause� button. CANCEL PROGRAMME

PROGRAMME START Turn on the tap and press the �Start/Pause� button. The indicator light of the �Start/Pause� button lights up. The indicator lamp shows the sequence reached by the programme. After starting the programme, the programme sequence indicator signals the Wash � �,
Rinse � � and Spin � � phases. Note: If there is a power interruption or if the appliance is disconnected during the cycle, the programme will run again from the point where it was interrupted.

1. Set the programme selector to Drain � �. 2. Press the �Start/Pause� button to start the �Drain� programme.

Whirlpool is a registered trademark of Whirlpool USA.

5019 312 00029
Black Process Plate