PHILIPS AZ2045/10
Owner's Manual

DIGITAL TUNER
3 Press and hold � or § until the frequency in the display starts running. � The radio automatically tunes to a station of sufficient reception. Display shows during automatic tuning. � If a FM station is received in stereo, is shown. 4 Repeat steps 2-3 if necessary until you find the desired station. � To tune to a weak station, press � or § briefly and repeatedly until you have found optimal reception.

CD
After all stations are stored, the first autostore preset station will then automatically play. To listen to a preset or autostore station Press the PRESET (up or down) buttons once or more until the desired preset station is displayed.

CD
Note: CD play will also stop when: � the CD door is opened � the CD has reached the end � you select tape or tuner source. Selecting a different track � Press � or § on the set, once or repeatedly to select. � In the pause/stop position, press 2; to start playback.

CASSETTE RECORDER
2 Press PROG. � If you attempt to program without first selecting a track number, is shown. 3 Repeat steps 1-2 to select and store all desired tracks. � Display: if you try to program more than 20 tracks. Reviewing the program In the stop position, press and hold PROG until the display shows all your stored track numbers in sequence.

Changing tuning grid (some versions only) In North and South America the frequency step between adjacent channels in the AM and FM band are 10 KHz and 100 KHz respectively. In the rest of the world this step is 9 KHz and 50 KHz. Usually the frequency step has been preset in the factory for your To improve radio reception: area. � For FM, extend, incline and turn the telescopic 1 Check that the set is completely switched off. aerial. Reduce its length if the signal is too strong. 2 To select 9KHz: Simultaneously, press MODE and � For MW (AM), the set uses a built-in aerial. Direct PRESET DOWN on the set. this aerial by turning the whole set. 3 Switch the set on to TUNER and then release the controls. Programming radio stations � To select 10KHz: Repeat steps 1-3 but in step 2, You can store up to a total of 30 radio stations in the simultaneously, press MODE and PRESET UP on memory, manually or automatically (Autostore). the set. � When you tune to radio stations, the display Manual programming shows tuning in either steps of 9 kHz or 10 kHz. 1 Tune to your desired station (see Tuning to radio � All preset and autostore stations will be stations). affected and you may need to reprogramme 2 Press PROG to activate programming. stations. 3 Press PRESET DOWN/ UP once or more to select a preset number. CD PLAYER 4 Press PROG to confirm. Playing a CD 5 Repeat steps 1-4 to store other stations. This CD player plays Audio Discs including Note: You can erase a preset station by storing CD-Recordables and CD-Rewritables. another frequency in its place. 1 Press y to on, then SOURCE to select CD. Autostore � if no CD is inserted. Autostore automatically starts programming radio 2 Insert a CD with the printed side facing up and stations from preset 1. Available stations are close the CD door. programmed in order of waveband reception strength: � Display: total number of tracks and playing time. FM, followed by MW (AM). Any previous presets e.g. � is shown if you have inserted a manually programmed will be erased. non-finalized CD-R(W). � Press PROG for 4 seconds or more to activate 3 Press 2; to start playback. autostore programming. � if your CD contains non-audio � The display shows AUTO, program blinks, files followed by the radio station details when 4 To pause playback press 2;. Press 2; again to stored. (See 5) resume play. 5 To stop CD playback, press 9.

Finding a passage within a track 1 Press and hold � or §. � The CD is played at high speed and low volume. Erasing a program 2 When you recognize the passage you want, release You can erase the program by: � or § to resume normal playback. � pressing 9 twice � is displayed briefly and Note: During a CD program or if shuffle/ repeat disappears. active, searching is only possible within a track. � selecting TAPE or TUNER source. Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback, and combine the modes with PROGRAM. shuffle � tracks of the entire CD/ program are played in random order shuffle and repeat all � to repeat the entire CD/ program continuously in random order repeat all � repeats the entire CD/ program repeat (and shuffle repeat) � plays the current (random) track continuously 1 To select play mode, press MODE once or more.

CASSETTE RECORDER Cassette playback 1 Press y to on, then SOURCE to select TAPE. � Display: shows throughout tape operation. 2 Insert a cassette and close the door. 3 Press PLAY 2 to start playback. 4 To pause, press PAUSE ;. Press again to resume. 5 Press SEARCH 5 or 6 to fast wind the tape. 6 To stop the tape, press STOP 9. � The keys are automatically released at the end of a tape, except if PAUSE ; has been activated.

2 Press 2; to start playback if in the stop position. GENERAL INFORMATION ON RECORDING 3 To select normal playback, press MODE repeatedly � Recording is permissible insofar as copyright or. until the various modes are no longer displayed. other rights of third parties are not infringed. � You can also press 9 to cancel your play mode. � For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been Programming track numbers broken. This deck is not suited for recording on In the stop position, select and store your CD tracks in CHROME (IEC II) or METAL (IEC IV) type cassettes. the desired sequence. Up to 20 tracks can be stored in � The best recording level is set automatically. the memory. Altering the VOLUME, DBB or BASS, MID & 1 Press � or § on the set to select your desired HIGH controls will not affect the recording. track number. � To protect a tape from accidental erasure, break out the tabs. If you wish to record again, cover the tabs with a piece of adhesive tape.