|
|
|
Who's Online
There currently are 6020 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Extension and Stock Stop BA162
WARNING Read and understand the manual for the use of the tool with this accessory.
Extension and Stock Stop - This attachment allows extra support for longer workpieces. Assembly 1. Unplug the saw. Lock the miter saw table in the 0 degree miter position, lower head assembly and lock head in the down position. NOTE: The stock stop can be mounted on the left or right side of saw to suit your operation. 2. Tilt saw back on its side to expose bottom side of base. 3. Slide adjustable stock stop on back rail of extension arm (Figure 1 & 2). 4. Slide extension arm through first pair of 1/2" diameter holes on outside of miter saw base (Figure 3). 5. Find the second pair of holes underneath miter saw base. Place "U" bracket over hole nearest to the front edge of the miter saw (Figure 3). 6. Slide extension arm through both the second pair of holes and "U" bracket. Make sure the extension arm passes completely through the second pair of holes (Figure 3). 7. Tighten hex bolt on "U" bracket with wrench to hold extension arm in place (Figure 3). 8. Repeat steps 5 - 7 for other side of miter saw. 9. Move adjustable stock stop as shown in Figure 4.
HEX BOLT BOULON HEXAGONAL "U" BRACKET SUPPORT EN U WING SCREW VIS � OREILLES EXTENSION ARM BRAS DE RALLONGE STOCK STOP BUT�E DE MAT�RIAU WING SCREW VIS � OREILLES STOCK STOP BUT�E DE MAT�RIAU
FIG. 1
FIG. 2
EXTENSION ARM BRAS DE RALLONGE
Rallonge et butée de matériau BA162 !
AVERTISSEMENT
Il convient de lire et de comprendre le manuel pour l'utilisation de l'outil avec cet accessoire.
FIG. 3
Rallonge et butée de matériau - Cet accessoire offre un support complémentaire pour les ouvrages plus longs. Assemblage 1. Débranchez la scie. Bloquez la table de la scie à onglet à la position onglet 0 degré, abaissez la tête et bloquez la tête en position abaissée. REMARQUE : La butée de matériau peut être montée sur le côté gauche ou droit de la scie en fonction de votre opération. 2. Inclinez la scie sur son côté de manière à exposer le fond de la base. 3. Faites glisser la butée de matériau réglable sur le rail arrière du bras de rallonge (Figures 1 et 2). 4. Faites glisser le bras de rallonge à travers la première paire de trous de 1/2 po de diamètre sur l'extérieur de la base de la scie à onglet (Figure 3). 5. Repérez la deuxième paire de trous sous la base de la scie à onglet. Placez le support en U par-dessus le trou le plus rapproché du bord avant de la scie à onglet (Figure 3). 6. Faites glisser le bras de rallonge à travers la deuxième paire de trous aussi bien que le support en U. Assurez-vous que le bras de rallonge passe entièrement à travers la deuxième paire de trous (Figure 3). 7. Serrez le boulon hexagonal sur le support en U à l'aide de la clé en vue de tenir le bras de rallonge en place (Figure 3). 8. Répétez les étapes 5 à 7 pour l'autre côté de la scie à onglet.
12.19a
1/2" DIA. HOLE TROU DE 1/2 po DE DIAM�TRE
FIG. 4
EXTENSION AND STOCK STOP RALLONGE ET BUT�E DE MAT�RIAU
Extension and Stock Stop
50
45
40
35
30
9. Déplacez la butée de matériau réglable, comme illustré dans la Figure 4.
2 610 991 820 10/96
PRINTED IN U.S.A.
|
|
|
> |
|
