|
|
|
Who's Online
There currently are 6022 guests and
21 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great site, I always find all the manuals I need and i can't find anywhere else. PDF for the Sony PCM 3348 is complete and scan is good quality. Thank you!
;
It was a complete manual as stated. Very good source for older product manuals. Thanks
;
Scan quality is very good. Price is very reasonable. If you're looking to purchase a copy of this manual, this is the one to get.
 ;
Perfect for my use.Could have better pictures,but otherwise perfect ;)
;
This is one of four manuals I have downloaded recently.
Purchase was very straight forward and the authorising email arrived in about 4 hours.
The quality of the scan is good. Print is clear and square to the page edges.
Listening to FM and AM Broadcasts
Tuning in a Station
On the unit ONLY:
1 Press FM/AM.
The unit automatically turns on and tunes in the previously tuned station (either FM or AM). The Powered Rolling Panel automatically opens. � Each time you press the button, the band alternates between FM and AM.
1 Tune in the station you want to preset.
� See �Tuning in a Station.�
MHz
2 Press SET.
2 Start searching for stations.
On the unit: Press and hold TUNING � / + for more than 1 second. On the remote control: Press and hold 1 / 4 or ¢ / ¡ for more than 1 second.
3 Press PRESET � / + to select a
preset number.
PREV NEXT
The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in. If a program is broadcast in stereo, the STEREO indicator lights up. To stop during searching, press TUNING � / + (or 1 / 4, ¢ / ¡).
4 Press SET again.
The tuned station in step 1 is stored in the preset number selected in step 3. � Storing a new station on a used number erases the previously stored one.
When you unplug the AC power cord or if a power failure occurs The preset stations will be erased in a few days. If this happens, preset the stations again.
When you press TUNING � / + (or 1 / 4, ¢ / ¡) briefly and repeatedly The frequency changes step by step.
To change the FM reception mode
FM MODE STILL
When an FM stereo broadcast is hard to receive or noisy, press FM MODE (STILL) on the remote control so that the MONO indicator lights up on the display. Reception improves. To restore the stereo effect, press FM MODE (STILL) again so that the MONO indicator goes off. In this stereo mode, you can hear stereo sounds when a program is broadcast in stereo.
Tuning in a Preset Station
1 Press FM/AM.
The unit automatically turns on and tunes in the previously tuned station (either FM or AM). The Powered Rolling Panel automatically opens. � Each time you press the button, the band alternates between FM and AM.
Presetting Stations
You can preset 30 FM and 15 AM stations. In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method. � There is a time limit for performing the following steps. If the setting is canceled before you finish, start from step 1 again.
2 Select a preset number.
On the unit: Press PRESET � / +. On the remote control: Press the number buttons.
For preset number 5, press 5. For preset number 15, press +10 then 5. For preset number 20, press +10, then 10. For preset number 25, press +10, +10, then 5. For preset number 30, press +10, +10, then 10.
� 12 �
English
|
|
|
> |
|
