|
|
|
Who's Online
There currently are 5610 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
;
Well Well Well!!!! Good manual perfect for my hobby!!! As Before you have done a very well done work!!!! Thank you
;
Super nice! Good to have a manual in digital format.
;
Great job supplying the manual.
Many of these products weerepretty obscure, so it was great that you had
the manual for it!
;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
SETTING THE CLOCK REMOTE CONTROL
Notes concerning use: In this example, clock is set for 24-hour (0:00) sysPress the TUNING/TIME ( or ) button to adjust or if the operation becomes erratic. Periodically clean transmitter LED on the remote con(Main unit operation) trol and sensor on the main unit with a soft cloth. Exposing sensor on the main unit to strong light may interfere with operation. Change lighting or the directem. the hour. Replace batteries if the operating distance is reduced
CD-BA1200H
6
0.2 6 m tion of the unit.
the time by 1 hour. Hold it down to advance continuously.
Press the TUNING/TIME ( or ) button once to (8" 20') Keep the remote control away from moisture, excessive heat, shock, and vibrations.
ON/ STAND-BY CLOCK 1 5
automatically to "PM".
When the 12-hour display is selected, "AM" will change 1
MEMORY/SET 7 Press the MEMORY/SET button.
TUNING/TIME ( )
1 Press ON/STAND-BY button to enter the stand8 Press the TUNING/TIME ( or ) button to adjust
RESETTING THE MICROCOMPUTER
Reset microcomputer under the following condiWithin 5 seconds, press the MEMORY/SET button. ON/ advance from "59" to "00". If the operation is not correct.
2 Press the CLOCK button.
by mode. the minutes.
3
X-BASS/ DEMO
Press the TUNING/TIME ( or ) button once to tions: advance time by 1 minute. Hold it down to change To erase all of the stored memory contents (clock and time in 5 minute intervals. EQUALIZER timer settings, tuner and CD presets). The hour setting will advance even if minutes If the display is not correct. STAND-BY
9 MEMORY/SET button. 1 Press ON/STAND-BY button to enter the standby mode.
OPERATION MANUAL
�6�
Press TUNING/TIME ( or ) button to select the
2 Whilst pressing down / button and the 4
time display mode.
EQUALIZER/X-BASS/DEMO button, hold down the ON/STAND-BY button for at least 1 second. "CLEAR AL" will appear. The operation explained above will erase all data stored after a few seconds. in memory including clock timer settings, and tuner
The clock starts operating from "0" second. (Seconds are not displayed.) And then the clock display will disappear Caution:
To see the time display: and CD presets.
Press the CLOCK button.
0:00 AM 12:00
The time display will appear for about 5 seconds.
"0:00" The 24-hour display will appear. Note:
The clock display will flash on and off at push of the (0:00 23:59) CLOCK button when the AC power supply is restored
"AM 0:00" The 12-hour display will appear. a failure occurs or after the AC power lead is
(AM 0:00 PM 11:59)
disconnected. If this happens, follow the procedure below to change the clock time.
"AM 12:00" The 12-hour display will appear.
(AM 12:00 PM 11:59)
Note that this can only be set when the unit is first installed or it has been reset.
To change the clock time: 1 Press the CLOCK button. 2 Within 5 seconds, press the MEMORY/SET button. 3 Perform steps 6 9 above.
5 Press MEMORY/SET button. To change the time display mode:
Perform steps 1 2 in "RESETTING THE MICROCOM-
PUTER".
2 Perform steps 1 9 above.
|
|
|
> |
|
