SHARP CDC430H
Service Manual

SETTING THE CLOCK PREPARATION FOR USE

1
Notes concerning use: Press ON/STAND-BY switch to enter the stand-by mode. Replace the batteries if control distance decreases or oper-

(0:00) system.
and sensor on the main unit with a soft cloth.

In this example, clock is set for the 24-hour Press the CLOCK button. ation becomes erratic.

2

3 Within 3 seconds, press MEMORY/SET button. Periodically clean transmitter LED on the remote control 4
(8" 20') CLOCK Keep the remote control away from moisture, excessive heat, shock, and vibrations.
1 1 5 SET "AM 12:00" � The 12-hour display will appear.

ON/ Exposing sensor on the main unit to strong light may indisplay mode. STAND-BY terfere with operation. Change lighting or the direction of 0.2 6 m

Press TUNING/TIME ( or ) button to select the time

(0:00 23:59) (AM 0:00 PM 11:59) MEMORY/ (AM 12:00 PM 11:59)

"0:00" � The 24-hour display will appear. the unit.

"AM 0:00" � The 12-hour display will appear.

CD-C430H,CP-C430H

TUNING/TIME

5

Press the MEMORY/SET button. ( )

6 Press TUNING/TIME ( or ) button to adjust the hour.

2

Press TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continuously. When the 12-hour display is selected, "AM" will change automatically to "PM". RESETTING THE MICROCOMPUTER
To erase all of the stored memory contents (clock and timer Press TUNING/TIME ( o r ) button to adjust the

7 Press MEMORY/SET button. Reset microcomputer under the following conditions: 8
The hour setting will not even if minutes advance
by mode.

3

4 minutes. settings, tuner and CD presets).

1,2

0:00 AM 12:00 If the operation is not correct. 2

Press button for at least 0.5 seconds to change the time If the display is not correct. in 5-minute intervals.

1

from "59" to "00". Press ON/STAND-BY (POWER) switch to enter the stand-

5 9 Press the MEMORY/SET button.

OPERATION MANUAL

�6�

6 In event of a failure or when the AC power lead

The clock starts operating from "0" seconds. (Seconds are Press and hold down VOLUME button, the not displayed.) button and ON/STAND-BY (POWER) switch all at the Note: same time. Hold them for at least 1 second.

2

7 occurred or when the AC power lead was disconnected.

is disconnected, the clock display will go out. When AC power supply is restored, the clock display will flash on and off to indicate time when the power failure

If this happens, follow procedure below to change the clock time.

To change the clock time: 8

1 Press the MEMORY/SET button. 2 Perform steps 6 9 above. 9

When the ON/STAND-BY switch is set to STAND-BY.

1 Press the CLOCK button. 2 Within 3 seconds, press the MEMORY/SET button. 3 Perform steps 6 9 above.

When the ON/STAND-BY switch is set to ON.

To see time display: (When the power is ON)

Press the CLOCK button.

The time display will appear for about 3 seconds.

To switch the time display mode:

1 Press ON/STAND-BY switch to enter the stand-by mode. 2 Press and hold down VOLUME button, the

button and ON/STAND-BY switch all at the same time. Hold them for at least 2 seconds. (Refer to RESETTING THE MICROCOMPUTER on page 17.)

3 Perform steps 1 9 above.

Note: The operation explained above will erase all data stored in memory, such as clock timer settings, tuner and CD presets.