|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
have download a number of manuals todate , most are excellant, one or two sometimes a little difficult to read but a least avaialable, great site .
Brad.
;
Excellent had everything I wanted, very happy with purchase
 ;
This service is relatively cheap, document is fast available, schematic is readable.
Thanks.
;
So far I´m a satisfied customer. I have only downloaded "TECHNICS SX-KN470 Service Manual" maybe I will use it later.
Best regards
Peter
;
Good manual. It is complete and of high quality, both text and graphics. The schematics are with the original big size, so it can be viewed or printed without any loss of resulution and sharpness.
SETTING CLOCK RESETTING THE MICROCOMPUTER
In this example, clock is set for the 24-hour (0:00) system. Reset microcomputer under the following conPress ON/STAND-BY button to enter the stand-by mode.
q To erase all of the stored memory contents (clock and timer q If the display is not correct. q If the operation is not correct. Within 5 seconds, press the MEMORY/SET button. settings, tuner and CD presets). Press the CLOCK button.
(Main unit operation)
ditions:
1 2
Press TUNING/TIME ( or ) button to select the time
2
display mode. Whilst pressing down 0 button and the X-BASS/ DEMO (0:00 23:59) second.
q �CLEAR AL� will appear. �AM 0:00� �The 12-hour display will appear. button, hold down the ON/STAND-BY button for at least 1 �0:00� �The 24-hour display will appear.
3 1 Press ON/STAND-BY button to enter the stand-by mode. 4
CD-DP2500W/DK2500W
�AM 12:00� �The 12-hour display will appear. q The operation explained above will erase all data stored in q Note that this can only be set when the unit is first inCD presets. stalled or it has been reset. (AM 12:00 PM 11:59) memory including clock timer settings, tuner and
(AM 0:00 PM 11:59) Caution:
5 Press the MEMORY/SET button. Illustration:CD-DP2500W 6 Press TUNING/TIME ( or ) button to adjust the hour.
q Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. q When the 12-hour display is selected, �AM� will change automatically to �PM�.
7 Press the MEMORY/SET button. 8 Press TUNING/TIME ( or ) button to adjust the minutes. q Press the TUNING/TIME ( or ) button once to advance time by 1 minute. Hold it down to change the time in 5 minute intervals. q The hour setting will not even if minutes advance from �59� to �00�.
OPERATION MANUAL
�8�
9 Press the MEMORY/SET button.
q The clock starts operating from �0� second. (Seconds are not displayed.) And then the clock display will disappear after a few seconds.
To see the time display:
Press the CLOCK button. q The time display will appear for about 5 seconds. Note: q The clock display will flash on and off at push of the CLOCK button when the AC power supply is restored after a failure occurs or after the AC power lead is disconnected. If this happens, follow procedure below to change the clock time.
To change the clock time:
1 Press the CLOCK button. 2 Within 5 seconds, press the MEMORY/SET button. 3 Perform steps 6 9 above.
Illustration:CD-DP2500W
To change the time display mode:
Perform steps 1 2 in the section �RESETTING THE MICROCOMPUTER�. 2 Perform steps 1 9 above.
|
|
|
> |
|
