|
Who's Online
There currently are 5718 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Quality scan, great manual. I solved my problem with this manual.
;
The AKAI 1720 model reel to reel tape recorder described in this Manual is quite an old unit - circa late 1960's. As a consequence, the description of the mechanical details - and adjustments thereof - is quite critical. The manual does this quite well. The schematics are also well presented and have detailed PCB overlays. Probably the only negative is that some half-tone detail has been lost from the original manual as it has been scanned in simple B&W.
;
Perfect source for service manuals: fast and professional transaction; high quality, perfect readable and largely scaleable PDF; complete schemes, diagrams and spare part list. Tnx a lot, cu again!!!!
;
I got your link from a friend and I must say that I am really satisfied with your service. Specially this B&O manual I didn't find anywhere on the web... but you could deliver it :-) . You deliver very fast and the copy is of good quality. So your webpage is bookmarked. Thanks
;
This was the Sony CCU-500A Service manual I was looking for.
The price was reasonable.
The permission to download was quck.
I will use Owner-Manual.com for all my manual needs.
SECTION 1 SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the �S curve check� in �CD section adjustment� and check that the S curve waveform is output three times. WRITING OF FOCUS/TRACKING AUTO GAIN DATA General CD palyers using digital servo ICs automatically adjust the focus/tracking gain each time the disc is changed. In this unit, the gain of the standard disc (YEDS-18) is written in the non-volatile memory (IC203:X24C01S) of the servo board so that the gain need not be re-adjusted when changing discs. Therefore, if the servo board, IC203 of the servo board, or optical pick-up has been replaced, be sure to write the auto gain data. 1. Connect TP (ADJ: Pin 3 of CN515) to GND (Ground), and turn ON the POWER switch. 2. Insert the test disc (YEDS-18). (The TOC data of the disc will be read.) This memorizes the auto gain data of the test disc. Note: � If the disc is replaced without turning OFF the power, the auto gain data of the last disc inserted will be memorized. � If the POWER switch is turned ON without connecting TP (ADJ) to GND, the auto gain data will not be memorized when the disc is inserted, and the data memorized the last time will be taken as the focus/tracking data.
IC202 IC104 IC105 IC102 CN515 CN514 CN513 321 ADJ AFJ
FLUORESCENT INDICATOR TUBE FULL LIGHTING MODE 1. Connect TP (AFJ:Pin 2 of CN515) to GND (Ground), and turn ON the POWER switch. 2. The bridge check (check for short-circut between pins of the S RAM (IC202 of the servo board)) is performed, and all the FL tubes light up if there is no bridge. 3. When a key other than the p(stop) key is pressed, the corresponding FL tubes lights up. Each time the p(stop) key is pressed, all the FL tubes light up. [SERVO BOARD] � Conductor Side �
�3�
|
|
|
> |
|