SONY CFDS500
Owner's Manual

English

Information
For customers in the USA
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Owner's Record
The model number is located at the bottom and the serial number is located in the battery compartment. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No.

On operation

Precautions
On safety
� As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. � Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further. � Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this player. Attempting to do so may damage the player. Do not use such discs.

� If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the CD player section. Should this occur, the player will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate. � If the player has not been used for a long time, set it in the playback mode to warm it up for a few minutes before inserting a cassette.

Troubleshooting
General
The power does not come on.
� Make sure the batteries are inserted correctly. � Replace all the batteries with new ones if they are weak. � You cannot turn on the player with the remote when you operate the player on batteries.

The tape does not move when you press an operation button.
� Close the cassette compartment securely.

Tape Player

Optional accessories

Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 3.2-ohm loads, both channels driven from 150 - 6,300 Hz; rated 1.8 W per channel-minimum RMS power, with no more than 10 % total harmonic distortion in AC operation.

Sony MDR headphone series

WARNING
To prevent fire or shock hazard, do not expose the player to rain or moisture.

The REC z button does not function or the tape does not play or record.
� Make sure the safety tab on the cassette is in place.

Poor or distorted playback, recording or erasing quality.
� Clean the heads, pinch roller and capstan with a cleaning swab slightly moistened with cleaning fluid or alcohol. � Replace all the batteries with new ones if they are weak. � TYPE II (high position) or TYPE IV (metal) tape is being used. Use TYPE I (normal) tape only. � Demagnetize the heads using a commercially available tape head demagnetizer.

The power is not on, and "bAttErY" and �Error� are displayed alternately.
� Make sure the batteries are inserted correctly. � Replace all the batteries with new ones if they are weak.

Other specifications
CD player section
System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20 000 Hz +1/�2 dB Wow and flutter Below measurable limit

CD Radio CassetteCorder
Operating Instructions
This symbol is intended to alert the user to the presence of uninsulated �dangerous voltage� within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

For customers in the USA
Please register this product on line at http://www.sony.com/productregistration. Proper registration will enable us to send you periodic mailings about new product, services and other important announcements. Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification. Thank you.

Notes on cassettes
� Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. Side A

There is no audio.
� Adjust the volume. � Unplug the headphones when listening through speakers.

Cleaning the cabinet
� Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine.

� Reorient or relocate the receiving antenna. � Increase the separation between the equipment and receiver. � Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. � Consult the dealer or an experienced radio/ TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Noise is heard.
� Someone is using a portable telephone or other equipment that emits radio waves near the player. tMove the portable telephone, etc., away from the player.

Lens

On power sources
� For AC operation, use the supplied AC power cord; do not use any other type. � The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. � Unplug the player from the wall outlet when it is not to be used for an extended period of time. � For battery operation, use six size D (R20) batteries. � When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. � The nameplate indicating operating voltage, power consumption, etc. is located at the bottom. Tab for side B

Tab for side A

CD Player
The CD does not play or �no dISC� lights in the display even when a CD is in place.
� Place the CD with the label surface up. � Clean the CD. � Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation. � The CD-R/CD-RW was not finalized. Finalize the CD-R/CD-RW with the recording device. � There is a problem with the quality of the CDR/CD-RW, recording device or application software.

� The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback.

CAUTION
The use of optical instruments with this product will increase eye hazard.

Notes on CDs
� Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out.

WARNING

Pinch roller

Erase head

CFD-S400 CFD-S500
Sony Corporation ©2001 Printed in China

Radio section
Frequency range FM: 87.5 - 108 MHz AM: 530 - 1 710 kHz Antennas FM: Telescopic antenna AM: Built-in ferrite bar antenna

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the appliance.

The sound drops out.

� Reduce the volume. � Clean the CD, or replace it if the CD is badly damaged. � Place the player in a location free from vibration. � Clean the lens with a commercially available blower. � The sound may drop out or noise may be heard when using poor quality CD-Rs/CDRWs or if device or application software. recording there is a problem with the

Capstan Record/playback head

For customers in Canada
To prevent electric shock, match wide blade of plug to wide slot, fully insert.

On placement
� Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. � Do not place the player on an inclined or unstable place. � Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. � If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun. � Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet. � Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. � Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. � Do not stick paper or sticker on the CD, nor scratch the surface of the CD. � After playing, store the CD in its case. If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error.

Remote
The remote does not function.
� Replace all the batteries in the remote with new ones if they are weak. � Make sure that you are pointing the remote at the remote sensor on the player. � Remove any obstacles in the path of the remote and the player. � Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. � Move closer to the player when using the remote. After trying the above remedies, if you still have problems, unplug the AC power cord and remove all the batteries. After all the indications in the display disappear, plug the power cord and insert the batteries again. If the problem persists, please consult your nearest Sony dealer.

Cassette-corder section
Recording system 4-track 2 channel stereo Fast winding time Approx. 120 s (sec.) with Sony cassette C-60 Frequency response TYPE I (normal): 80 - 10 000 Hz

3-238-274-11 (1)

Power Sources
B C

Radio
Reception is poor.
� Reorient the antenna to improve FM reception.

General
Speaker Full range: 10 cm dia., 3.2 ohms, cone type (2) Outputs Headphones jack (stereo minijack) For 16 - 68 ohms impedance headphones Power output 2.3 W + 2.3 W (at 3.2 ohms, 10% harmonic distortion) Power requirements For CD radio cassette-corder: 120V AC, 60 Hz 9 V DC, 6 size D (R20) batteries For remote control: 3 V DC, 2 size AA (R6) batteries Power consumption AC 20 W Battery life For CD radio cassette-corder: FM recording

1 to AC IN
A
Connect the AC power cord A or insert six size D (R20) batteries (not supplied) into the battery compartment B . Notes
� Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player. � To use the player on batteries, disconnect the AC power cord from the player. � When you operate the player on batteries, you cannot turn on the player using the remote.

About CD-Rs/CD-RWs
This player can play CD-Rs/CD-RWs recorded in the CD-DA format*, but playback capability may vary depending on the quality of the disc and the condition of the recording device. * CD-DA is the abbreviation for Compact Disc Digital Audio. It is a recording standard used for Audio CDs. If you have any questions or problems concerning your player, please consult your nearest Sony dealer. The audio is weak or has poor quality.
� Replace all the batteries with new ones if they are weak. � Move the player away from the TV.

2 to a wall outlet

� Reorient the player itself to improve AM reception.

Sony R20P: approx. 13.5 h Sony alkaline LR20: approx. 20 h
Tape playback

Preparing the remote C
Insert two size AA (R6) batteries (not supplied).

Sony R20P: approx. 7.5 h Sony alkaline LR20: approx. 15 h
CD playback

The picture of your TV becomes unstable.
� If you are listening to an FM program near the TV with an indoor antenna, move the player away from the TV.

Replacing battery
With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones.

Sony R20P: approx. 2.5 h Sony alkaline LR20: approx. 7 h
Dimensions Approx. 386 � 166 � 252 mm (w/h/d) (15 1�4 � 6 5�8 � 10 inches) (incl. projecting parts) Mass Approx. 3.3 kg (7 lb. 4 oz) (incl. batteries) Supplied accessory AC power cord (1) Remote control (1) Headphones (1) (CFD-S500 only) Design and specifications are subject to change without notice.