|
|
|
Who's Online
There currently are 5966 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
as a first-time user and buyer from this site, i found the overall service outstanding!! this product is a godsend as, without it, i would never have been able to find my way around and use my machine as intended. i will certainly use this site again as required. many many thanx!!
;
This manual is exactly what I needed. This site always has every manual I need, and it is also much less expensive then most other sites. This is the only manual site I will use.
 ;
Useful manual, good scan, worth the pay if you find the unit difficult to operate.
;
Exactly as described, the full user-manual (145 pages). Perfect.
THE CONDENSER
The condenser and ducting should be cleaned 3 or 4 times a year or more frequently if the dryer is in constant use. See �CLEANING THE CONDENSER� opposite. NOTE: The condenser will discolour through use.
CLEANING THE CONDENSER
CAUTION: For maximum efficiency, the plates are made from very thin aluminium and are easily damaged. Do not try to poke anything between the plates or use a hard object or tool for cleaning. At all times, handle the condenser carefully and avoid crushing the plates.
� �
REMOVING THE CONDENSER
� �
Remove the condenser (see opposite). Flush the fluff from between the plates under running water and carefully shake off excess water.
Slide the condenser grille catch to the left. Firmly pull the condenser out.
RE-INSTALLING THE CONDENSER
�
�
�
Carefully push the condenser back into the machine, until it is pushed fully home and a �click� is heard. Ensure all lint and fluff is removed from around the grille seal before closing or water may leak. IMPORTANT: The dryer may leak if the condenser is not correctly re-installed.
�
Whilst the condenser is removed, clean as much fluff as possible from inside the ducting by reaching a hand into the machine. In particular, keep the passage from the fan clear (on the right hand side of the condenser duct). After cleaning, re-install the condenser (see opposite).
�
J
MII CONDENSER
Reverse door and fit to dryer in closed position. Refit screws (G) and hinge cover (F). Open the door. screw (J) and remove buffer. Remove screws (C) and latch plate (D). Remove hinge cover screw (E). Close the door. Open the door. Undo screw (A) remove switch strike (B) and replace screw. Undo
Your dryer is supplied with a reversible door. To change the direction of opening proceed as follows for your type of door.
Dryers fitted with hinge cover:-
REVERSING THE DOOR OPENING
Fit screw (E) to secure hinge cover. Remove screw (H) at top of door and refit switch strike (B) as shown. Refit buffer (J). Pull the hinge cover (F) forwards to remove it. Remove two outer screws (G). Remove door. Fit latch plate (D) with screws (C).
J
B
FPL �98
Open the door. Undo screw (A) remove switch strike (B) and replace screw. Undo screw (J) and remove buffer. Remove screws (C) and latch plate (D). Remove hinge block screws (E). Remove door from hinge blocks.
Refit latch plate (D) with screws (C). Remove screw (H) at top of door and refit switch strike (B) as shown. Refit buffer (J). Fit door to hinge blocks and secure with screws (E).
1
Dryers fitted without hinge cover:-
J
B
E
A
3
C
D
D
H
C
B
E
Remove hinge screws (F) and hinge (G) and refit to opposite side as shown.
2
J
F
4213 094 57186
G
|
|
|
> |
|
