|
|
|
Who's Online
There currently are 5232 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
;
The manual was properly scanned and perfectly readable. The only small problem is that I couldn't use my dear Ctrl + F to find a word I needed.
;
Nothing wrong with the manual or the delivery - came to me the same day I ordered it. But afterwards I realized that I ordered the wrong manual. Probably better with the Quick start - version. So maybe it would be better if we could see a list with inhold for each manual before ordering?
 ;
Bought T4850 High End Tuner a few years ago, but i didn't know where all the buttons were used for. So i purchased the owners manual. Perfect! Just what i needed.
s
Are the doors not closed completely? Close the doors firmly. If they do not close completely, see �The doors will not close completely� later in this section. Are the condenser coils dirty? This prevents air transfer and makes the motor work harder. Clean the condenser coils. Refer to the �Cleaning� section. Are the door gaskets not sealed all the way around? Contact a technician or other qualified person. NOTE: Your new refrigerator will run longer than your old one due to its high-efficiency motor.
s s
Off-taste, odor or gray color in the ice
Are the plumbing connections new, causing discolored or off-flavored ice? Discard the first few batches of ice. Have the ice cubes been stored too long? Throw old ice away and make a new supply. Does the freezer and ice bin or bucket need to be cleaned? See the �Cleaning� or �Ice Maker and Storage Bin/ Bucket� section. Has food in the freezer or refrigerator been wrapped properly? Use airtight, moisture-proof packaging to help prevent odor transfer to stored food. Does the water contain minerals (such as sulfur)? A filter may need to be installed to remove the minerals. Is there a water filter installed on the refrigerator? Gray or dark discoloration in ice indicates that the water filtration system needs additional flushing. Run additional water through the water dispenser to flush the water filtration system more thoroughly (at least 2 to 3 gal. [8 to 12 L] or 6 to 7 minutes initially). Discard discolored ice.
s
s s
s
The refrigerator seems to make too much noise
s
The sounds may be normal for your refrigerator. See the �Normal Sounds� section.
s
s
The ice maker is not producing ice or not enough ice
s
Has the ice maker just been installed? Wait 72 hours for full ice production to begin. Once your refrigerator is cooled, the ice maker should produce 70 to 120 cubes every 24 hours. Is the freezer temperature cold enough to produce ice? Wait 24 hours after ice maker hook-up for ice production. See the �Setting or Using the Controls� section. Is the ice maker wire shutoff arm in the OFF (arm up) position (on some models)? Lower the wire shutoff arm to the ON (arm down) position. See the �Ice Maker and Storage Bin/Bucket� section. Is the ice maker switch in the OFF (right) position (on some models)? Move ice maker switch to the ON (left) position. See the �Ice Maker and Storage Bin/Bucket� section. Is the water line shutoff valve to the refrigerator turned on? Turn on the water valve. See the �Water Supply Connection� section. Does the ice maker mold have water in it or has no ice been produced? Make sure your refrigerator has been connected to a water supply and the supply shutoff valve is turned on. See the �Water Supply Connection� section. Is an ice cube jammed in the ice maker ejector arm? For models with an interior ice bin, remove the ice from the ejector arm with a plastic utensil. For models with an ice bucket located on the freezer door, access the ice maker by depressing the ice sensor door on the upper left side of the freezer interior. While depressing the sensor door, lift the ice maker service door and remove the ice from the ejector with a plastic utensil. See the �Ice Maker and Storage Bin/Bucket� section. Has a large amount of ice just been removed? Allow 24 hours for ice maker to produce more ice. Are the controls set correctly? See the �Setting or Using the Controls� section. Is there a water filter installed on the refrigerator? The filter may be clogged or installed incorrectly. Check the filter installation instructions to ensure that the filter was installed correctly and is not clogged. If installation or clogging is not a problem, call a technician or other qualified person.
s s s
s
The ice dispenser will not operate properly
Is the freezer door closed completely? Push the door firmly shut. If it will not shut all the way, see �The doors will not close completely� later in this section. Is the ice bin or bucket installed correctly? For models with an interior ice bin, push the ice bin in all the way. If the ice bin does not go in all the way, it may not be put in straight. Pull it out and try again. For models with an ice bucket located on the freezer door, the bucket should sit level. To remove the bucket, press the release button on the right side of the bucket and lift straight up. Replace the bucket in the door making sure it is properly aligned and snapped securely into place. Refer to the �Ice Maker and Storage Bin/Bucket� section. Has the wrong ice been added to the bin or bucket? Use only cubes produced by the current ice maker. If other cubes have been added, remove all cubes and check to see that none have become stuck in the delivery chute. Has the ice frozen in the ice bin or bucket? Shake the ice bin or bucket to separate cubes. If cubes do not separate, empty bin or bucket and wait 24 hours for ice to restock. Has the ice melted around the auger (metal spiral) in the ice bucket? Dump the ice cubes and clean the ice bucket completely. Allow 24 hours for the ice maker to restock. Do not try to remove the melted ice with a sharp object. You could damage the ice bucket. Is ice stuck in the delivery chute? Clear the ice from the delivery chute with a plastic utensil. Do not use anything sharp to remove the ice. You could cause damage. Is the ice dispenser stalling while dispensing �crushed� ice? Stop dispensing ice. Change the ice button from �crushed� to �cubed.� Depress the ice dispenser arm using a sturdy glass. If cubed ice dispenses correctly, depress the button for �crushed� ice and begin dispensing again. Refer to the �Water and Ice Dispensers� section. Is there ice in the bucket? See �The ice maker is not producing ice� earlier in this section. Has the dispenser arm been held in too long? Release dispenser arm. Ice will stop dispensing when the arm is held in too long. Wait three minutes for dispenser motor to reset before using again. It is best to take large amounts of ice directly from the ice bin or bucket, not through the dispenser.
s
s
s
s
s
s
s
s
s
s
s
s
s
NOTE: If not due to any of the above, there may be a problem with the water line. Call for service.
s
19
|
|
|
> |
|
