|
|
|
Who's Online
There currently are 5913 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a service manual in every sense of the word ( French and German versions of the text are included, as well as English..)
There are explanations of the mechanical and electrical functions, plenty of mechanical drawings, and the needed schematics. The quality of the scanning is excellent - all the component values are clearly legible - and very usefully there are pcb component layouts, so you can find a component on the schematic, and then very quicky pinpoint its physical location on the relevant pcb.
I cannot see how I can give this manual any less than the maximum 5 stars! Great value for money, which will pay for itself immediately. Excellent all round!
;
the manual is great and especially hard to find... thanks for the great service and having a hard to find manuel_
;
Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product. You will receive $2.50 of store credit for Your review.
;
hat alles sehr gut geklappt. Das Servicemaual ist gut zu verwenden. Die Pläne und Schrift
ist klar und leserlich. Außerdem preiswert. Grüße an alle Hifi-Bastler
;
I got the manual quickly after the payment was transfered (1 day). The manual was exactly what i needed and the updates via e-mail were great. Thanx!
DV MECHANICAL ADJUSTMENT MANUAL VII
3-11.Band Adjuster, S Reel Table Assy and TG2 Arm Block Assy
1.
1) 2) 3) 4) 5)
Removal procedure
Remove the screw (special head screw M1.4 � 2.5) 1. Remove the band A of the TG2 arm block and remove the band adjuster 2. Remove the S reel table assy 3. Remove the tension spring (tension regulator spring) 4. Remove the TG2 arm block assy 5.
2.
1) 2)
Attachment procedure
Install the S reel table assy 3. Apply grease in the TG2 arm pivot shaft B. Amount of grease: a ball of 1.0 mm diameter of grease Re-application of grease to the point which is greased already before is not necessary. 3) Hold the TG2 arm block assy 5 with tweezers and insert it in the TG2 arm pivot shaft B. 4) Hook the tension spring (tension regulator spring) 4 on the TG2 arm block 5 with tweezers so that the hook faces downward. 5) Hook the tension spring (tension regulator spring) 4 on the LS chassis block assy (the second hook from the rear end). 6) Hook the A portion of the band on the claw of the band adjuster 2. 7) Hold the band adjuster with tweezers as shown in C. Insert the band into groove of the S reel table assy while rotating it, and insert the adjuster�s dowel into the dowel hole D of the LS chassis block assy. 8) Install the band adjuster 2 with the screw (special head screw M1.4 � 2.5) 1. Tightening torque: 0.059 ± 0.01N�m (0.6 ± 0.1kgf�cm) 9) Perform the TG2 FWD Position Adjustment referring to section 4-1. 10) Perform the FWD Back-tension Adjustment referring to section 4-4. 11) Perform the Reel Torque Check referring to section 4-2.
The spring hook faces downward. TG2 arm 5 block assy
3 S reel table assy
1 Screw (M1.4 � 2.5) 2 Band adjustor
4 Tension spring (Tension regulator)
A C
Dowel D Hole D Band
Shaft B
Key Points in Re-assembling
Second from the rear end The spring hook faces downward.
Apply Grease Points to be noted
During installation, apply grease in the TG2 arm pivot shaft hole. Amount of grease: a ball of grease of 1.0 mm diameter Re-application of grease to the point which is greased already before is not necessary. B
� 22 �
|
|
|
> |
|
