|
|
|
Who's Online
There currently are 5708 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site.
Thank you very much
;
Exactly what was needed to assess the product - excellent value and great service
;
A site where discontinualed schematic diagrams and back dated information can be found on discontinued radios tv's and any electronic equipment can be found. Newer manuals either Service and operating manuals. Radio amateurs should find this site a great source for ham radio equipment manuals. I will return to this site should I need information on any electrical equipment. priced easy to download in a PDF format and print pages need to undertake the repair.
;
Quality scan of the original. All the detail necessary to troubleshoot, repair and adjust the unit. I'm sure I will be downloading more manuals in the future as the need arises.
ALIGNMENT INSTRUCTIONS
3.The adjustment of SCREEN 3-1. Confirm the presetting IBRM data of EEPROM according to CRT. 3-2. Press the [S2] KEY of SVC Remocon, horizontal line will be displayed. 3-3. Adjust SCREEN V/R of FBT so that the horizontal line reach the cut-off point. 3-4 To be completed adjustment of screen. Press the [S2] key to escape screen adjustment mode. 4.The adjustment of FOCUS 4-1. Receive PAL RETMA PATTERN(signal of company:2CH., PAL-B). 4-2. Adjust the picture to best distinct picture of 350 Line by revolve Focus Volume. 5.The adjustment of WHITE BALANCE 5-1. NITSUKI Setting : Set Nitsuki to the Auto Mode , Reference to the B , and System to the PAL . 5-2. Setting the Normal Stats 5-2-1. Adjust Picture to Normal mode. 5-2-2. Adjust the Gain of Nitsuki to suitability by manual when condition is Normal. - Adjust the standard illumination take within limit bright of Nitsuki and luminosity of SET into acount. - Exhortative Standard illumination, : High 70Cd/ , LOW BEAM : about 15Cd/ 5-2-3. Press the [S8]key of SVC remocon to adjustment of Whit Balance. X=0.288, Y=0.301 5-2-4. Memorize in Nitsuki after Adjustment of White Balance. 5-3. Adjustment of White Balance 5-3-1.Receive Nitsuki signal. 5-3-2.Adjust Picture to Normal mode. 5-3-3.The Adjustment of High Beam : Adjust R-DRIVE and G-DRIVE to R,G,B BAR come to center. 5-3-4.The Adjustment of Low Beam : Adjust R-BIAS and G-BIAS to R,G,B BAR come to center. 5-3-5.Repeat 5-3-3 and 5-3-4 to R,G,B BAR come to within center 1. 6.The adjustment of GEOMETRY 6-1. Press the [S-6]key on the SVC remocon to call up the Geometry mode. And then, Geometry OSD will be displayed. 6-1-1. All adjustment is base on PAL(50Hz), but it can be base on NTSC(60Hz) in case of need. 6-2. The adjustment of VERTICAL CENTER 6-2-1.Receive PAL RETMA pattern(signal of company:PAL-B 2CH). 6-2-2.Press the PR up/down Keys( ) to select V CENTER. Adjust with Vol Up/Down ( ) keys so that the center mark of the CRT may be located on the horizontal line in the middle of the pattern. In case of no center mark, adjust with Vol Up/Down ( ) keys to obtain a vertically symmetrical pattern.
-7-
|
|
|
> |
|
