|
|
|
Who's Online
There currently are 5911 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
excellent quality, contains circuits and scan quality, 110 pages
;
It was easy done, and I got exactly what I was looking for.
;
The manuel was exactly what I needed and I received it promptly. Thanks
;
Thanks to Owner-Manuals.com! This manual was exactly what I needed. As Amana was purchased by Maytag and later by Whirlpool, there was no way to receive it from their websites. I was lucky to find this resource.
 ;
Great to be able to set channels again, on an old but stoll fine working TV
Enjoying music in the remote zone
Zone 2 indicator
Off Zone 2
Sleep
On/Standby
Level /
Input Selector buttons Input source buttons
Zone 2
Using the buttons on the DTR-7.3
1. Press the Zone 2 button on the DTR-7.3. 2. Select an input source. After pressing the Zone 2 button, you must press an input source button within 8 seconds. The indicator above the input source button lights green. In this condition, even if you change the input source for the main zone, the input source for the remote zone (Zone 2) will not change. Ex.: When the CD button is pressed.
Using the remote controller
After pressing the Zone 2 button, press the On/Standby button within 5 seconds.
Select an input source: After pressing the Zone 2 button, press an Input Selector button within 5 seconds.
To select the same source for the remote zone that is selected for the main zone, press the Zone 2 button again until �Z2 Sel:SOURCE� appears in the display. In this condition, if you change the input source for the main zone, the input source for the remote zone (Zone 2) will change as well.
When �Z2 Sel:Off� is displayed, the output to the remote zone is turned off. Notes: � If a sleep time is set with the Sleep button, the output to the remote zone will also turn off when the sleep time elapses. � The ZONE 2 terminal is an analog output. Digital signals are not output. If no sound is heard from the selected input source, check if the component is connected to the analog inputs. � If the Rec Out button is pressed in the main room while someone is using the system in the remote zone, the Zone 2 function will be deactivated and the source will turn off in the remote zone. � If you select FM (or AM) with the input source buttons when the source for the remote zone (Zone 2) is set to AM (or FM), the output for the remote zone also changes to AM (or FM). � 7.1-channel playback in the main room is disabled if the Surr Back/Zone 2 setting in the Surr Back/Zone 2 sub-menu of the Hardware Setup Menu is set to �Zone 2.� � When you are using the remote zone (Zone 2), system operation will not work. � When you are using the remote zone (Zone 2), the Pure Audio setting will not work. � When you are not using the remote zone (Zone 2), press the Off button to turn off the Zone 2 indicator. (Using the remote controller, press the Zone 2 button and then the Standby button.)
Note: After you press the Zone 2 button on the remote controller, the STANDBY indicator on the DTR-7.3 flashes for five seconds. During this time, you will not be able to perform operations in the main zone using the remote controller.
Adjusting the volume for the remote zone
When the remote zone (Zone 2) speakers are connected to the SURR BACK/ZONE 2 SPEAKERS terminals, or to an amplifier connected to the SURR BACK/ZONE 2 PRE OUT terminals, adjust the volume as shown below. Adjusting the volume (using the remote controller): After pressing the Zone 2 button, the Standby indicator on the DTR7.3 will flash for 5 seconds. During this time press the Level / button.
Note: When the remote zone (Zone 2) speakers are connected to the pre-main amplifier that is connected to the ZONE 2 terminal of the DTR-7.3, adjust the volume for the remote zone at the pre-main amplifier.
36
|
|
|
> |
|
