|
|
|
Who's Online
There currently are 6022 guests and
21 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Super Anleitung. Ordentliche Auflösung. Das ganze noch in Deutsch wäre zu schön. Alle Datenblätter sind sauber Kopiert und alle Leitungswege sind sauber ausgeführt
;
Thanks God for the internet and thanks for the service like this - proffessional solution on time.
;
About the service it's very fast and reliable. About the manual the quality is high enough to read even the tiniest details on the wiring diagrams so you can't ask much more than that, let it alone for a manual of a product from 20 years ago. Thank you, very satisfied.
;
The downloaded quality was as good as the orignial
 ;
This is a great and complete Service Manual for the Sharp GF8585HB. Giving full and detailed technical insight. Good to find these manuals online.
DV-620H DV-620S
From (2) Following playback, jump test mode "3" Key input PLAY TEST 30000001 00000000 Because a tray opens, a disk is published.
"Open/Close" Key input PLAY TEST DD000303 ******** It becomes following playback state. (******** is a sector ID.) A test jump can be done by inputting the following key from the remote controller. Key Jump Key 1 -1 3 4 -102 6 7 -510 9 C -511 M 2 -765 Repeat 5 -766 A-B 8 -7000 Program Before skipping. -15000 After skipping. Next replay Layer Jump Offset adjustment mode "Menu" Key input FOCUS 000000** 000000** FOCUS offset adjustment mode FOCUS 000000** 000000++ The part of ++ is changed at every key input. Connect the L side of the voltmeter to the IC702 (pin 18) and its H side to the IC702 (pin 17). Adjust the output voltage to a range of -30mV to +10mV with the cross key "�" or "�". With the cross joint key "�", �, 5 step change After it confirms that a spindle motor stops, "RETURN"key input (SPIN) (00000000 00000000) The offset adjustment of the spindle is done automatically. Jump 1 102 510 511 765 766 7000 15000
TRACK offset adjustment mode TRACK 000000** 000000++ The part of ++ is changed at every key input. "Retern" key input ADJUST COMPLETE 00**00** 000000** "Rapid return" key End of adjustment For the section of **, the adjustment results are displayed. The indication contents mean the "focus offset adjustment value", "track offset adjustment value" and "spindle offset adjustment value" from the left. Cut a power source when you finish adjustment. Push a "Rapid return" key when it is adjusted again. When a "return" key is pushed, it is returned in the beginning of servo adjustment mode. Connect the L side of the voltmeter to the IC702 (pin 16) and its H side to the IC702 (pin 15). Adjust the output voltage to a range of -30mV to +10mV with the cross key "�" or "�". With the cross joint key "�", �, 5 step change
"Return" key
[ROM RENEWAL MODE]
1. A DVD itself and a personal computer are articulated as the right figure. Software for the renewal is started more. 2. A power source is put with pushing a DVD's own playback key and a halt key at the same time. (It keeps pushing it for about three seconds.) R : OK It is displayed.
3. When "a lateral" is inputted in accordance with the personal computer display and data transfer indication is shown and renewal process is started normally when an ENTER key is pushed. W : STR It is displayed.
Personal computer (DOS)
4. When renewal is completed normally. W : END It is displayed.
5. "STOP" key is surely pushed if renewal is completed and the display of above NO.4 is confirmed.It is made to turn off POWER after that.
Fixture for the ROM renewal DIGITAL It is articulated to the OUT terminal connection child.
DVD itself
15
|
|
|
> |
|
