|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
complete part-lists and pcb layout, schematic diagram is good enlargable,
;
Excellent, fast delivery, excellent product. Good luck!
;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
� LFE (Low Frequency Effect) signal
2 Press C/c to select
TV Virtual Surround Settings (TVS)
When you connect a stereo TV or 2 front speakers, TVS (TV Virtual Surround) lets you enjoy surround sound effects by using sound imaging to create virtual rear speakers from the sound of the front speakers (L: left, R: right) without using actual rear speakers. TVS was developed by Sony to produce surround sound for home use using just a stereo TV. This function is designed to work with the LINE OUT L/R (AUDIO) jacks. Note that if you select one of the TVS settings, the player does not output Dolby Digital signals from the DIGITAL OUT (OPTICAL or COAXIAL) jack. (when you set �DOLBY DIGITAL� in �AUDIO SETUP� to �D-PCM�) (page 62)
DVP-NS315 DVP-NS415
Note
If �DTS� is set to �OFF� in �AUDIO SETUP,� the DTS track selection option will not appear on the screen even if the disc contains DTS tracks (page 62).
(SURROUND), then press ENTER repeatedly to select one of the TVS sounds.
Refer to the following explanations given for each item. � TVS DYNAMIC � TVS WIDE � TVS NIGHT � TVS STANDARD
TVS DYNAMIC
TV
To cancel the setting
Select �OFF� in Step 2.
To turn off the Control Bar
Press DISPLAY repeatedly until the Control Bar is turned off. NTVS DYNAMIC Creates virtual rear speakers from the sound of the front speakers (L, R) without using actual rear speakers (shown below). This mode is effective when the distance between the front L and R speakers is short, such as with built-in speakers on a stereo TV.
TV
NTVS NIGHT Large sounds, such as explosions, are suppressed, but the quieter sounds are unaffected. This feature is useful when you want to hear the dialog and enjoy the surround sound effects of �TVS WIDE� at low volume. NTVS STANDARD Creates virtual rear speakers from the sound of the front speakers (L, R) without using actual rear speakers. The virtual speakers are reproduced as shown in the illustration below. Use this setting when you want to use TVS with 2 separate speakers.
L R
SUR
ENTER DISPLAY
L: Front speaker (left) R: Front speaker (right) : Virtual speaker NTVS WIDE Creates virtual rear speakers from the sound of the front speakers (L, R) without using actual rear speakers. The virtual speakers are reproduced as shown in the illustration below. This mode is effective when the distance between the front L and R speakers is short, such as with built-in speakers on a stereo TV.
z Hint You can also change the setting by pressing SUR (or SURROUND on the player) repeatedly.
1 Press DISPLAY twice during
playback.
The following Control Bar appears.
Notes
� When the playing signal does not contain a signal for the rear speakers, the surround effects will be difficult to hear. � When you select one of the TVS modes, turn off the surround setting of the connected TV or amplifier (receiver). � Make sure that your listening position is between and at an equal distance from your speakers, and that the speakers are located in similar surroundings.
,continued
44
45
� �TVS NIGHT� only works with Dolby Digital discs. However, not all discs will respond to the �TVS NIGHT� function in the same way. � If you use the DIGITAL OUT (OPTICAL or COAXIAL) jack and set �DOLBY DIGITAL� to �DOLBY DIGITAL� or �DTS� to �ON� in �AUDIO SETUP,� sound will come from your speakers but it will not have the TVS effect.
Displaying the Subtitles
Enjoying Movies
Changing the Angles
If various angles (multi-angles) for a scene are recorded on the DVD, � � appears in the front panel display. This means that you can change the viewing angle.
DVP-NS315 DVP-NS415
If subtitles are recorded on the discs, you can change the subtitles or turn them on and off whenever you want while playing a DVD.
DVP-NS315 DVP-NS415
SUBTITLE ANGLE
Sound Adjustments Enjoying Movies
1 Press SUBTITLE during playback. 1 Press ANGLE during playback.
The number of the angle appears on the display. The number in parentheses indicates the total number of angles.
2(7)
The following display appears. The number in parentheses indicates the total number of available subtitles.
() 1 8 :ENGLISH
2 Press SUBTITLE repeatedly to
select the language.
Depending on the DVD, the choice of language varies. When 4 digits are displayed, they indicate a language code. Refer to �Language Code List� on page 68 to see which language the code represents.
2 Press ANGLE repeatedly to select
the angle number.
The scene changes to the selected angle.
Note
Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the DVD.
To turn off the subtitles
Select �OFF� in Step 2.
Note
Depending on the DVD, you may not be able to change the subtitles even if multilingual subtitles are recorded on it. You also may not be able to turn them off.
46
47
1-11
|
|
|
> |
|
