CASIO DW9350J-1T
Owner's Manual

1583/1584-2
Moving the watch to a position that is parallel to the ground and then tilting it towards you more than 40 degrees causes the backlight to light.

To input new Telememo data
Cursor
A
Text Area

B

Parallel to ground

More than 40°

C L
Number Area

D

1. In the Telememo Mode, press B and D at the same time to display the new data screen. � The new data screen is the one that is blank (contains no name and telephone number). � If the message FULL appears in the text area of the display, it means that memory is full. To store more data, you will first have to delete some of the data stored in memory. 2. Hold down A until the flashing cursor appears in the text area of the display. 3. Use B and D to change the character at the cursor position in the text area. The character changes in the following sequence.

� The backlight turns off in about two seconds, even if you keep the watch pointed towards your face. � The backlight may not light if the face of the watch is more than 15 degrees off the parallel as shown below. Make sure that the back of your hand is parallel to the ground.

[New Data Screen] Press D
(space) :

Press B
A to Z (alphabet) . 0 to 9 -

to (Japanese) /

Parallel to ground

More than 15 degrees too high

More than 15 degrees too low

� Static electricity or magnetic force can interfere with proper operation of the auto light switch. If the backlight does not light, try moving the watch back to the starting position (parallel with the ground) and then tilt it back toward you again. If this does not work, drop your arm all the way down so it hangs at your side, and then bring it back up again. � Under certain conditions the backlight may not light until about one second or less after turn the face of the watch towards you. This does not necessarily indicate malfunction of the backlight. Warning! � Never try to read your watch when mountain climbing or hiking in areas that are dark or in areas with poor footing. Doing so is dangerous and can result in serious personal injury. � Never try to read your watch when running where there is danger of accidents, especially in locations where there might be vehicular or pedestrian traffic. Doing so is dangerous and can result in serious personal injury. � Never try to read your watch when riding on a bicycle or when operating a motorcycle or any other motor vehicle. Doing so is dangerous and can result in a traffic accident and serious personal injury. � When you are wearing the watch, make sure that its auto light switch is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury.

� Holding down either button changes the character at high speed. � You can input Japanese characters (katakana), English alphabetic characters, numbers, and symbols in the text area. For a complete list of characters you can input, see �Character List� at the back of this manual. 4. When the character you want is at the cursor position, press C to move the cursor to the right. 5. Repeat the steps 3 and 4 until your text is complete. � You can input up to eight characters for the name. 6. After you input a name, use C to move the cursor to the number area. � The text area can hold up to eight characters. When the cursor is located at the eighth space of the text area, moving the cursor to the right causes it to jump down to the first digit in the number area. When the cursor is at the 12th digit of the number area, moving it to the right causes it to jump back up to the first character of the text area. 7. Use B and D to change the character (hyphen, number, or space) at the cursor position in the number area. The character changes in the following sequence. Press D
x 0 to 9 (space)

Press B � Holding down either button changes the character at high speed. 8. When the character you want is at the cursor position, press C to move the cursor to the right. 9. Repeat steps 7 and 8 until you complete number input. � You can input up to 12 digits for the number. 10. After inputting your data, press A to store it. � When you press A to store data, the message SORT appears on the display for a few seconds. After the sort operation is complete, the cursor appears in the text area, ready for input a new Telememo data item. 11. Input more data (staring from step 3) or press A again to return to the Telememo Mode data screen (without the cursor). � If you do not perform any button operation for few minutes while the cursor is on the display, the watch automatically returns to the Telememo Mode data screen. � The text area of the display can show only five characters at a time, so longer text scrolls continuously from right to left.

To turn the auto light switch on and off
In the Timekeeping Mode, hold down D for one second to turn the auto light switch on ( AUTO displayed) and off ( AUTO not displayed). � Frequent use of the auto light switch greatly reduces the charge of the storage battery. If you use the auto light switch often, be sure to leave the watch where it is exposed to sunlight during the day time so it can recharge the storage battery. 10 minutes exposure to sunlight provides enough of a charge for about 10 to 20 auto light switch operations. � The AUTO indicator is on the display in all modes while the auto light switch is turned on.

To recall Telememo data
In the Telememo Mode, press D to scroll forward through stored data items or B to scroll in reverse. � Holding down either button scrolls through the data at high speed.

To edit Telememo data items

TELEMEMO MODE
Mode indicator

Name
A B

Remaining memory
C L D

The Telememo Mode lets you store up to 30 pairs of name and telephone number data. Data is automatically sorted based on the characters of the name. You can recall data by scrolling through it on the display. � See the �CHARACTER LIST� at the back of this manual for details on how the watch sorts data. � If there is no data stored in the Telememo Mode, the message N O - D A T A appears following the remaining memory screen. � The data item on the display when you exit the Telememo Mode appears first the next time you enter the Telememo Mode. � In the Telememo Mode, press L to illuminate the display. Pressing L illuminates the display even while you are inputting data.

1. In the Telememo Mode, scroll through the data items and display the one you want to edit. 2. Hold down A until the flashing cursor appears in the text area of the display. 3. Use C to move the flashing cursor to the character you want to change. 4. Use B and D to change the character. � For details on inputting characters, see �To input new Telememo data� (steps 3 for name input and 7 for number). 5. After making the changes that you want, press A to store them and return to the Telememo Mode data screen.

To delete Telememo data
1. In the Telememo Mode, scroll through the data items and display the one you want to delete. 2. Hold down A until the flashing cursor appears in the text area of the display. 3. Press B and D at the same time to delete the data item. � At this time the cursor appears in the text area, ready for input. 4. Input data or press A to return to the Telememo Mode data screen.

Telephone number