perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
Text excerpt from page 4 (click to view)
OPERATION
Before using
Remove all securing tapes. Wash inside the appliance with lukewarm water and bicarbonate of soda (5 ml to 0.5 litre of water). Do not use soap or detergent as the smell may linger. Dry thoroughly.
Rear spacers
In the bag with the documentation, there are two spacers which must be fitted as shown in the figure. Slacken the screws and insert the spacer under the screw head, then re-tighten the screws.
Control panel
MAX
ON
min
D594
Door reversal directions
A
A - Pilot light B - Thermostat control
B
1. Disconnect from the electricity supply. 2. Gently lay the fridge on its back with the top held away from the floor by 5-8 cm (2-3 inches) of packing; 3. Remove the ventilation grill (D). 4. remove the bottom hinge (E) by unscrewing its three fixing screws; Important 5. Slide out the fridge door from pin (G), unscrew the latter and then refit it on the opposite side; 6. remove the two plugs of the door (where available), discovering the holes for the hinge pins, assemble them on the opposite side; 7. reassemble the door; 8. using a 10 mm spanner, unscrew the hinge pin (E) and reassemble it on the opposite side of the hinge; 9. reassemble the lower hinge (E) on the opposite side, using the screws previously removed. Slide the hole cover (F) out of the ventilation grille (D) by pushing it in the direction of the arrow and reassemble it on the opposite side; 10.refit the ventilation grille (D), clipping it into place; 11. Unscrew the handle. Refit it on the opposite side after having pierced the plugs with a punch. Cover the holes left open with the plugs supplied in the documentation pack.
F
E
E F F D
To Start the Appliance
Allow the appliance to stand for 2 hours after installation. Plug in the appliance and switch on at the mains supply. Turn the thermostat control knob (B) to a medium setting. The pilot light (A) will illuminate. Leave the appliance for approximately 4 hours to allow the correct temperature to be reached before placing food inside. To switch off the appliance turn the thermostat control knob to position �O� . During prolonged periods of abnormally hot weather, if the thermostat is set on too high a number, the cooling system may operate continuously and the fridge cooling plate may not defrost. Turning the knob to a lower number will cause the automatic defrosting to resume.
F
Fresh food refrigeration
To obtain the best performance, do not store warm food or evaporating liquids in the refrigerator; do cover or wrap the food, particularly if it has a strong flavour. Do not cover the shelves with any protective material, such as paper, cardboard or plastic, which may obstruct the air circulation through them. To help you use your refrigerator correctly, here are some more useful hints: Raw meat (beef, pork, lamb & poultry or chicken): wrap in polythene bags and place on the glass shelf above the salad crispers. Meat can only be stored safely in this way for one or two days at the most. Fruit & vegetables: these should be thoroughly cleaned and placed in the bottom salad crisper(s). Butter & cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible. Milk bottles: these should have a cap and should be stored in the bottle rack on the door.
G
Setting the temperature
The temperature within the appliance is controlled by the thermostat control knob situated at the top of the appliance. To operate the appliance proceed as follows: Turn the thermostat control beyond the «I» position. Position min = minimum coldness Position max = maximum coldness Turn the thermostat dial to the required position. The intermediate position is usually the most suitable. The thermostat setting can vary as the temperature inside the refrigeration compartment depends on the following factors: � room temperature � how often the door is opened � how much food is stored � position of the appliance 4
Important
After completion of the door reversing operation, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdryer on a low setting.
