Irrespectively of this manual exist only germany language, it's useful - although i need some additional task to translate: My english is bad, but usable - but i really dont speak germany. :)
Excellent service from this company (including a total refund on an earlier purchase when through no fault of the company the manual was incomplete). I have purchased several manuals which I have been very satisfied with, as I am with this one. Highly recommended.
Manual was delivered in a timely manner and was all in English as advertised. The manuals I received when we moved into our flat were in German, Italian, and French. Having never used a steamer before, and not speaking/reading German very well, I needed an English Manual. this was a huge help.
Text excerpt from page 10 (click to view)
COOL , HEAT and FAN ONLY Operation ,
1. If the AUTO mode is not comfortable , you may manually override the settings by using COOL, DRY, HEAT( HEAT PUMP units only), or FAN ONLY modes. 2. Push the TEMP button to set the desired room temperature. When in COOLING mode, the most comfortable settings are 21 C or above. When in HEATING mode, the most comfortable settings are 28 C or below. 3. Push the FAN SPEED to select the FAN mode of AUTO, HIGH, MED or LOW. 4. Push the ON/OFF button. The operation lamp lights and the air conditioner starts to operate per your settings. Push the ON/OFF button again to stop this unit operation.
1
TEMP Button : Push the TEMP button to decrease the indoor temperature setting or to adjust the TIMER in a counter-clockwise direction. MODE Select Button: Each time you push the button, a mode is selected in a sequence that goes from AUTO COOL HEAT and FAN as the following figure indicates:
AUTO COOL DRY
2
DRY
HEAT
FAN
NOTE: HEAT only for Heat Pump
3
SWING Button: Push this switch button to change the louver angle . RESET Button: When the RESET button is pushed, all of the current settings are cancelled and the control will return to the initial settings. ECONOMIC RUNNING Button: Push this button to go into the Energy-Saving operation mode. LOCK Button: Push this button to lock in all the current settings. To release settings, push again. CANCEL Button: Push this button to cancel the TIMER settings. TIMER Button: This button is used to preset the time ON (start to operate) and the time OFF (turn off the operation). ON/OFF Button: Push this button to start the unit operation. Push the button again to stop the unit operation. FAN SPEED Button: This button is used for setting Fan Speed in the sequence that goes from AUTO LOW MED to HIGH, then back to Auto. TEMP Button : Push the button to increase the indoor temperature setting or to adjust the TIMER in a clockwise direction. VENT Button : Push this button to set the ventilating mode. The ventilating mode will operate in the following sequence :
Continuous Auto Off
4
NOTE
The FAN ONLY mode cannot be used to control the temperature. While in this mode, only steps 1 3 and 4 may be performed.
5
6 7 8 9 10
DRY OPERATION
1. Push the MODE button to select DRY. 2. Push the TEMP button to set the desired temperature from 21 C to 28 C. 3. Push the ON/OFF button. The operation lamp lights and the air conditioner starts to operate in the DRY mode. Push the ON/OFF button again to stop this unit operation.
NOTE
Due to the difference of the set temperature of the unit and the actual indoor temperature, the Air Conditioner when in DRY mode will automatically operate many times without running the COOL and FAN mode.
11
TIMER OPERATION
PUSH TIMER button to set the on and off times of the unit. 1. To set the STARTING time. 1.1 Please push the CANCEL button to cancel any former settings. 1.2 Push the TIMER button. The remote controller will show the TIMER and the signal "h" is shown on the display panel. The control is now ready to reset the TIMER ON to start the operation. 1.3 Push the TEMP button ( or ) to set desired unit START time . 1.4 After setting the TIMER there will be a one-half second delay before the remote controller transmits the signal to the Air Conditioner. Then, after approximately another 2 seconds ,the set temperature will re-appear on the digital display.
12
Ventilation Function is available for the Fresh Star Series.
