|
|
|
Who's Online
There currently are 5993 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellant!!! Very quick and easy....Best $4.99 I have spent in a very long time..
I highly recommend this.
;
Thanks so much for the Owner's manual for my Sony PS - FL1. I had purchased the turntable off of eBay. It came in and looked great. Packed well and appeared to be great. I balanced and aligned the tone are and hooked it up. When trying to play a record the tone are would move to the right place and just before it would drop to play it moved back off the edge of the record before touching down. I searched the net for an answer to this issue. No luck. Then I purchased the owners manual and sure enough there was a place to adjust where the stylus touched down. That adjustment solved the problem and saved me a $35 feet to have the player checked out. The manual is well written and easy to understand. It is a must have for anyone with this front loading Sony turntable.
;
Some years back I pruchased a Sansui G-9000. I had it cleaned up and a problem with the left channel repaired. When I got it back I hooked it up to my tape decks, turn tables, TV and it played great. The only thing I was not really satisfied with was the performance of my Graphic Equalizer. I purchased this owner's manual had poured myself a cup of coffee. The manual is well organized and written in plain language. It also contained the solution to my dissatisfaction. By using the preamp connections coupled I was able to run everything through my graphic equalizer and now enjoy the full potential of my complete system.
 ;
An excellent service for the price, however, it would also have been handy if the troubleshooter pages were included. The manual is only sent in the language of your country, thus it looks as though there are some pages missing. Otherwise highly recommended.
;
I am happy to get a rare TECHNICS SH-9090 Owner's Manual by PDF in clear copy.
Adjusting the shelves...
1. 2. 3. 4. First, remove food from shelf. Slide shelf straight out to stop. Lift front. Slide the rest of the way out.
Replacing
Shelf:
Shelf Guide
I. Fit back of shelf on top of guides with wire stops on the bottom of gurdes 2. Lrft front, slide shelf In until It clears gurde stops.
Removing crispers and crisper cover.. .
Removing the Crispers:
1 Slide crisper straight out to stop, lift front, then slrde the rest of the way out 2. Replace in the reverse order
Lift the Front, Then the Back.
Removing Cover:
1 Loftfront and remove the cover support 2. Loftout cover by pullrng up and out.
Replacing
Cover:
1 Fit back of cover into notch supports on walls of refrigerator, then lower front Into place 2. Replace cover support wrth the long tab towards the front. Note: If support needs adjustment, turn base right to lower, or left to ratse
Pull out to stop. ront and Pull Again.
Ice cube trays...
lo remove Ice:
l
Hold tray at both ends . Slightly twist
If cubes are not used, they may shrink. The movrng cold air starts a slow evaporation The longer cubes are stored, the smaller they get
Optional automatic ice maker.. .
Arm to Stop Ice Maker
l
l
It is normal for ice crescents to be attached by a corner. They ~111break apart easily You will hear water running when ice maker IS working. You�ll hear ice fall into the bin Don�t let these sounds bother you. The ice maker will not operate until the freezer IS cold enough to make Ice. This can take overnight. Because of new plumbing connections. the first Ice may be discolored or off-flavored Discard the first few batches of ice. If ice IS not being made fast enough and more ice IS needed, turn the Refrigerator Control toward a higher number. Wait a day and, if necessary, turn the Freezer Control toward A. If you remove the ice bin, raise the signal arm to shut off the ice maker. When you return the bin, push It all the way In and lower the arm to the ON position. If cubes are stated too long, they may develop an off-flavor...like stale water. Throw them away. They will be replaced. Cubes in the ice btn can also become smaller by evaporation The ice maker water supply should not be Softened water. The chemicals could damage the ice maker molds.
l
l
l
If you have the automatic Ice maker accessory or plan to add one later [Part No. ECKMF-83). there are a few things you will want to know
l
l
The ON/OFF lever IS a wire signal arm. Down...for making Ice automa-ically, Up...to shut off the Ice maker. Shake the bin occasronally to keep cubes separated, and to obtain increased storage capacity.
l l
l
6
|
|
|
> |
|
