|
|
|
Who's Online
There currently are 5100 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Reversing the door swing...
You can change the hinges on your refrigerator so the doors open the other way. You will need a #20 Torx head screwdriver. Refer to the instruction sheet included with your refrigerator.
Removing and adjusting the freezer shelf...
To remove the shelf: 1. Lift front slightly. 2. Lift back off supports. 3. Replace in reverse order. To adjust the shelf: 1. Remove shelf 2. Remove supports 3. Replace supports 4. Replace shelf
by sliding upwards. on desired level
Ice cube trays...
(Model ETISPK Only) If cubes are not used, they may shrink. The movIng cold arr starts a slow evaporation. The longer cubes are stored, the smaller they get. To remove ice: 1. Hold tray at both ends. 2. Twist slightly.
Automatic
ice maker...
l
If you have the automatic ice maker accessory, or if you plan to add one later (Part No. ECKMF-86), there are a few things you will want to know: l The ON/OFF lever is a wire signal arm. Down...for making ice automatically. Up...to shut off the ice maker. DO NOT TURN ICE MAKER ON UNTIL IT IS CONNECTED TO THE WATER SUPPLY. The dial or lever on the side of the ice maker changes the srze of the cubes l Shake the bin occasionally to keep cubes separated, and to obtain increased storage capacity . It IS normal for Ice crescents to be attached by a corner. They will break apart easily.
l
l
l
You will hear water running when ice maker is working. You�ll hear ice fall into the bin. Don�t let these sounds bother you. The ice maker will not operate until the freezer is cold enough to make ice. This can take overnight. Because of new plumbing connections, the first Ice may be discolored or off-flavored. Discard the first few batches of ice. If ice is not being made fast enough and more ice is needed, turn the Refrigerator Control toward a higher number, Wait a day and, If necessary, turn the Freezer Control toward A. If you remove the ice bin, raise the signal arm to shut off the ice maker. When you return the bin, push it all the way in and lower the arm to the ON position. If cubes are stored too long, they may develop an off-flavor...like stale water. Throw them away, They will be replaced. Cubes in the ice bin can also become smaller by evaporation. Good water quality is important for good ice quality It is not recommended that the ice maker be connected to a softened water supply. Water softener chemicals such as salt from a malfunctioning softener can damage the ice maker mold and lead to poor quality ice. If a softened water supply cannot be avoided, then it is important that the water softener be well maintained and operating properly.
l
l
l
LOWER SIGNAL ARM TO START IT
RAISE SIGNAL ARM TO STOP ICE
l
|
|
|
> |
|
