|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The purchased manual is an high quality scan of the original Philips paper-based Service Manual. I am very satisfied!
 ;
The purchased manual is an scan of the original Panasonic paper-based Service Manual. Unfortunately the contrast is not perfect, but I am satisfied anyway!
;
The purchased manual is an high-quality scan of the original JVC paper-based Service Manual. The Service Manual includes the Owner´s Manual, so you do not have to buy both of them.
;
It paid to find this Service Manual, couldn't find it anywhere else. Exactly what I wanted. Received within 24 hours.
;
Complete manual with clear schematic diagrams and printed circuit board layouts of two variants of the headset and the transmitter an old and a new version.
Also shows how the headset and the transmitter is opened and how transmitter and receivers can be adjusted and where to measure.
I had no problems to repair the headset using this service manual.
FIRMWARE RENEWAL MODE
1. Turn the power on and press [SELECT] button on the remote control unit to put the DVD player into DVD mode. Then remove the disc on the tray. (It is possible to move to F/W version up mode only when the DVD player in DVD mode with the tray opened.) 2. To put the DVD player into F/W version up mode, press [9], [8], [7], [6], and [SEARCH MODE] buttons on the remote control unit in that order. Fig. a appears on the screen.
"*******" differ depending on the models.
5. After programming is finished, the tray opens automatically. Fig. e appears on the screen and the checksum in (*3) of Fig. e.
"*******" differ depending on the models.
F/W Version Up Mode
Model No : ******* VERSION : *.**
VERSION : X5****_****.ab5 Completed SUM : 7ABC (*3)
F/W Version Up Mode
Model No : ******* VERSION : *.**
Please insert a DISC for F/W Version Up.
Fig. e Completed Program Mode Screen
6. 7.
EXIT: SELECT
Fig. a Version Up Mode Screen
8. 9.
The DVD player can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open. 3. Load the disc for version up. 4. The DVD player enters the F/W version up mode automatically. Fig. c appears on the screen. If you enter the F/W for different models, �Disc Error� will appear on the screen, then the tray will open automatically.
"*******" differ depending on the models.
At this time, no buttons are available. Remove the disc on the tray. Press [CH UP/DOWN] button on the unit to go to TV mode, or press [POWER] button on the unit to turn the power off. Press [SELECT] or [DVD PLAY] button on the remote control unit to put the DVD player into DVD mode again. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. g appears on the screen.
"*******" differ depending on the models.
MODEL : ******* Version : *.** Region : *
F/W Version Up Mode
Model No : ******* VERSION : *.** VERSION : X5****_****.ab5 Reading...(*2)
EEPROM CLEAR : CLEAR
EXIT: SELECT
Fig. g
10.Press [CLEAR] button on the remote control unit. Fig. h appears on the screen.
"*******" differ depending on the models.
Fig. c Programming Mode Screen
The appearance shown in (*2) of Fig. c is described as follows:
No. 1 2 3 Appearance Reading... Erasing... State Sending files into the memory Erasing previous version data
MODEL : ******* Version : *.** Region : * EEPROM CLEAR : OK
Programming... Writing new version data
EEPROM CLEAR : CLEAR
EXIT: SELECT
Fig. h
When �OK� appears on the screen, the factory default will be set. Then the firmware renewal mode is complete. 11.To exit this mode, press [CH UP/DOWN] or [SELECT] button to go to TV mode, or press [POWER] button to turn the power off. 1-7-1 T9000TEST
|
|
|
> |
|
