|
|
|
Who's Online
There currently are 5927 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great price, Quick delivery, the document was very usefull A+++++++++++++++
;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
Section
Audio Adjustments
11
M HPF: 31.540506380100125 160200 (Hz) M LPF: 1.622.53.15456.38 1012.516 (kHz) H HPF: 1.622.53.15456.38 1012.516 (kHz) 4 Press a or b to adjust the level of the selected speaker unit (filter). Each press of a or b increases or decreases the level of the selected speaker unit (filter). 0dB 24dB is displayed as the levelis increased or decreased. +6dB 24dB is displayed as the levelis increased or decreased, only if you haveselected L LPF. 5 Press SLOPE to select the slope of the selected speaker unit (filter). L LPF: 12 18 6 (dB/oct.) M HPF: 12 18Pass (0) 6 (dB/oct.) M LPF: 12Pass (0) 6 (dB/oct.) H HPF: 12 6 (dB/oct.) 6 Press PHASE to switch the phase of the selected speaker unit (filter). Each press of PHASE switches the phase between normal and reverse .
# You can adjust the parameters for other speaker units (filters) in the same way.
# SW2 is displayed only when the subwoofer output is on in the subwoofer output mode (SW1).
1 Press AUDIO and NEXT and then press SW1 to select the subwoofer output mode.
# To turn subwoofer output off, press SW1 again.
2 Press SW1 to turn subwoofer output on. SUB.W ON appears in the display. Subwoofer output is now on.
3 Press c or d to select the phase of subwoofer output. Press c to select reverse phase. Press d to select normal phase.
Adjusting subwoofer settings
When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer.
1 Press AUDIO and NEXT and then press SW2 to select the subwoofer setting mode. 2 Press c or d to select cut-off frequency. Each press of c or d selects cut-off frequencies in the following order: 506380100125 (Hz) Only frequencies lower than those in the selected range are output from the subwoofer.
English
7 Press BAND to cancel the network adjustment mode.
Using subwoofer output
This unit is equipped with a subwoofer output which can be switched on or off. When a subwoofer is connected to this unit, turn the subwoofer output on. The subwoofer output phase can be switched between normal and reverse.
3 Press a or b to adjust the output level of the subwoofer. Each press of a or b increases or decreases the level of the subwoofer. +6 24 is displayed as the level is increased or decreased.
En
49
|
|
|
> |
|
