|
|
|
Who's Online
There currently are 5970 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very happy to find this from owners-manual.com and the enclosed spec sheet as well.
Not longer available from Sony.
;
The Owner's manual was very helpful. The WEGA is about 35 years old and needed repair.
Your Website is pretty good und easily to handle.
Thank You
Carl-W. Lohmann
;
Perfect. Very good service and very good scanning quality. All sheets are very legible. Thank's
;
My first manual from Owner-Manuals.com but not the last! I am very satisfied with the easy ordering and promt delivery of a manual I did not find anywhere else.
 ;
This manual is very helpfull to use the Power Supply. All technical information has been available.
For service use the circuit diagrams are very good.
Thanks .
Using the Tuner
Presetting Stations
You can preset up to 30 FM stations and up to 15 AM (MW) stations.
CAUTION:
� Even if the system is unplugged or if the power failure occurs, the preset stations will be stored for about 24 hours. However, in case the preset stations are erased, you will need to preset the stations again.
� Preset numbers may have been set to factory test frequencies prior to shipment. This is not a malfunction. You can preset the stations you want into memory by following one of the presetting methods below.
To Change the FM Reception Mode
When you are tuned into an FM stereo broadcast, the �ST.� indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose stereo effect. FM AUTO mode is also useful to suppress static noise between stations. To enter Monaural mode while receiving an FM broadcast, press the FM/PLAY MODE button on the Remote Control until �FM MONO� appears on the display. Then, the �MONO� indicator lights up. Each time you press the FM/PLAY MODE button, the display alternates between �FM AUTO� and �FM MONO�.
FM/PLAY MODE
1
FM / AM
SET
STORED
+10 2
SET
or
FM = 30, AM = 15 When changing the Band
On the Remote Control
1 2 3
Select a band by pressing the FM/AM button.
Press the 5 or � button to tune in a station. Press the SET button.
Preset number �1� will blink for 5 seconds. Within 5 seconds, proceed to the next step. When the display returns to the one set in step 2 after 5 seconds, press the SET button again.
FM AUTO � FM MONO To restore the stereo effect, press the FM/PLAY MODE button on the Remote Control until �FM AUTO� appears on the display. Then, the �MONO� indicator goes out and the �ST.� indicator will light up.
4
Press the Numeric Keys, or the 3 or 2 button within 5 seconds to select the preset number.
Example:
Beat Cut (AM (MW) Reception)
Switching the Beat Cut mode may reduce beat noise. Each time you press the FM/PLAY MODE button while receiving an AM (MW) broadcast, the Beat Cut mode changes as follows. BEAT CUT 1 = BEAT CUT 2 = BEAT CUT 3 = BEAT CUT 4 = (back to the beginning)
FM/PLAY MODE
5 6
Press the SET button within 5 seconds.
�STORED� appears and after 2 seconds, the display returns to the broadcast frequency display. Set to the position where beat noise is small. � The best position will differ depending on the AM (MW) broadcast station being received.
Repeat above steps 1 to 5 for each station you want to store in memory with a preset number.
To change the preset stations, repeat the same steps as above.
� In AM (MW) broadcast, reception sensitivity will be changed by turning the AM (MW) loop antenna. Turn the AM (MW) loop antenna for best reception.
14
|
|
|
> |
|
