CASIO FT120HB-2AV
Owner's Manual

Module No. 1993/2075
ABOUT THIS MANUAL
B
B
P

1993/2075-1

v

A

C

A

C

� The operational procedures for Module 1993 and 2075 are identical. All of the illustrations in this manual show Module 1993. � Button operations are indicated using the letters shown in the illustration.

P

M
(MODE)

L

(LIGHT)

M

(MODE)

L

(LIGHT)

v

[Module 1993]

[Module 2075]

GENERAL GUIDE
� Press M to change from mode to mode. Each mode is explained in detail on the following pages. � In any mode, press L to illuminate the display. Identification (ID) Mode Vital Statistics Mode

v

Timekeeping Mode

Telememo Mode

A

C

Stopwatch Mode

Alarm Mode

P

M

L

TIMEKEEPING MODE
Graphic area Month � Day Year Day of week

In addition to normal timekeeping, the Timekeeping Mode is also used to set the current time and date, and to turn the EL alarm on and off. � In the Timekeeping Mode, graphic area indicates counting of seconds.

B A
P

C

To set the time and date
1. Press A while in the Timekeeping Mode. The seconds digits flash on the display because they are selected. 2. Press M to change the selection in the following sequence.

To turn the EL alarm on and off In the Timekeeping Mode, hold down B for one or two B seconds to toggle the EL alarm on ( displayed) and off A C ( not displayed). � The EL alarm on indicator remains on the display in all modes until you switch the EL alarm off. P � The above operation controls operation of the EL alarm only. It does not affect operation of audible tones and M signals.
L
EL alarm on indicator

� When an alarm is reached while the EL alarm is turned on, themay not of the backlight and the timing normal and tones flashing be exactly matched. This is of the alarm does not indicate malfunction.

Hour Minutes Seconds PM indicator

Seconds

Hour

Minutes

TELEMEMO MODE
Day Month Year

Mode indicator

Text area

3. While the seconds digits are selected (flashing), press B to reset the seconds to 00. If you press B while the seconds count is in the range of 30 to 59, the seconds are reset to 00 and 1 is added to the minutes. If the seconds count is in the range of 00 to 29, the minutes count is unchanged. 4. While any other digits (besides seconds) are selected (flashing), press B to increase the number. While the 12/24-hour setting is selected, press B to switch between the two formats. � Holding down B changes the current selection at high speed. � When the 12-hour format is selected, the 12H indicator appears on the display. With the 12-hour format, the P (PM) indicator appears on the display to indicate �p.m.� times. There is no indicator for �a.m.� times. � Selecting the 24-hour format causes the 24H and the 24 indicators to appear on the display. 5. After you set the time and date, press A to return to the Timekeeping Mode. � The day of the week is automatically set in accordance with the date. � The date can be set within the range of January 1, 1995 to December 31, 2039. � If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Timekeeping Mode automatically.

B A C

The Telememo Mode lets you store up to 20* pairs of name and telephone number data. Stored data is sorted automatically into alphabetic sequence based on the characters of the name. * The Telememo Mode shares memory with the Identification (ID) Mode. This means that the maximum number of Telememo Mode entries you can store is reduced by one each time you store Identification Mode.

M

L Number area

To check remaining memory

In the Telememo Mode, hold down B and C to display how much memory remains for input of data. The value that appears shows how many more data items (Telememo Mode and ID Mode) you can input.

� This watch has three built-in ID Mode titles, which are programmed in memory when you first purchase the watch and which are automatically set whenever the watch�s battery is replaced. Because of this, the remaining memory display shows a value of 17 (20 � 3) whenever it is performed immediately after you purchase the watch or have the battery changed.

BACKLIGHT
The backlight uses an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark. An EL alarm feature can be turned on so the backlight flashes whenever an alarm or hourly time signal sounds. � Pressing L in any mode illuminates the display for about three seconds, regardless of the EL alarm on/off setting. � The backlight of this watch employs an electro-luminescent (EL) light, which loses its illuminating power after very long term use. � The backlight remains lit for about three seconds from the point you press L, even if it already lit when you press L. If you keep L depressed for one or two minutes, the backlight will automatically turn off. � The illumination provided by the backlight may be hard to see when viewed under direct sunlight. � The backlight automatically stops illuminating whenever an alarm sounds. � The watch will emit an audible sound whenever the display is illuminated. It does not indicate malfunction of the watch.

To input new Telememo data
1. In the Telememo Mode, press B or C until the new data screen appears. B � If there is no Telememo data stored in memory yet, the A C new data screen appears as soon as you enter the Telememo Mode. � If the message FULL appears in the text area, it means that memory is full. To store more data, you will first have to delete some of the data stored in memory. 2. Press A and a cursor appears in the text area. M 3. Input a name in the text area and a telephone number in [New Data Screen] L the number area. Number area � You can input up to eight characters in the text area, and 12 digits in the number area.
Cursor
Text area

Use B and C to input characters, and M to move the cursor around the display. For details, see �How to input characters�. � Make sure that you distinguish between the letter O and the number 0 (zero). Inputting a zero for the letter O will affect automatic sorting. 4. After inputting your data, press A to store it and return to the Telememo Mode. � The text area can show only five characters at a time, so longer messages scroll continuously right to left.

v

M

L

12/24-hour format

v v

B