|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
;
Well Well Well!!!! Good manual perfect for my hobby!!! As Before you have done a very well done work!!!! Thank you
;
Super nice! Good to have a manual in digital format.
;
Great job supplying the manual.
Many of these products weerepretty obscure, so it was great that you had
the manual for it!
;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
RECORDING
Dubbing tapes (from tape deck 1 to tape deck 2)
1 Press TAPE to select tape deck 2 . 2 Load the prerecorded tape into tape deck 1 and a blank tape into tape deck 2. � Make sure that the tape in tape deck 1 has its full spool to the left. 3 Press DUBBING once for normal speed dubbing or twice within 2 seconds for high speed dubbing. � "NORMAL" (normal speed) or "FAST" (high speed) will be displayed and then followed by "DUBBING". � HSD flag appears on the display for high speed dubbing. � Dubbing will start immediately. � REC flag starts flashing. 4 Press STOP � to stop dubbing.
CLOCK
1 Load a blank tape into tape deck 2 and a disc into the disc tray. 2 Press CD to select CD mode . � You can program the tracks in the order you want them to be recorded (see Programming Tracks). If not, the tracks are recorded according to the selected disc. 3 Press RECORD to start recording. � REC flag starts flashing. � CD will start playback automatically. 4 Press STOP � to stop recording. You can view the clock (if it is set) at standby or any source mode. It will be displayed for about 7 seconds. � Press CLOCK�TIMER briefly. � �10:25� (the current time) will be displayed. � �--:--� will be displayed if the clock is not set.
Clock Setting
The clock is set in 24-hour mode, e.g. �00:00� or �23:59�. Before setting the clock, you must be in the View Clock mode. 1 Press CLOCK�TIMER to select clock mode. � �00:00� or the current time starts flashing. � �à , á , à , ë, � light up. � 2 Set the hour with à or á. 3 Set the minute with à or ë. 4 Press CLOCK�TIMER again to store the setting. � The clock starts running. � To exit without storing the setting, press STOP �.
Recording from other sources (only on tape
deck 2)
1 2 � 3 Load a blank tape into tape deck 2. Press CD, TUNER or AUX. Start playback of the selected source. Press RECORD to start recording. � REC flag starts flashing. 4 Press STOP � to stop recording.
Notes: � At the end of side A, flip the tapes to side B and repeat the procedure. � Dubbing of tapes is only possible from tape deck 1 to tape deck 2. � To ensure good dubbing, use tapes of the same length. � During high speed dubbing in Tape mode, the sound is reduced to a low volume. � You can switch to other source while dubbing.
Note: � During recording, it is not possible to listen to another sound source.
Notes: � During clock setting, if no button is pressed within 90 seconds, the system will exit clock setting mode automatically. � When a power interruption occurs, the clock setting is erased. � To set the time with RDS clock, see "Receiving RDS Radio Station" under TUNER section.
21
Untitled-26
21
6/15/00, 4:52 PM
3139 116 17942
English
CD Synchro Start Recording
View Clock
|
|
|
> |
|
