|
|
|
Who's Online
There currently are 5364 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good quality instructions manual. Very useful to me. Quick and excellent service from Owner-Manuals... Thanks !!!
;
Sono molto soddisfatto e, quando mi necessiterà, mi avvarrò nuovamente di questo servizio!
;
A comprehensive Operating and Service Manual. All schematics are complete and easy to read. The PCB drawings and complete parts list are very helpful. I would definitely recommend this manual.
;
SCANNING OF HIGH QUALITY
VERY, VERY HIGH VELOCITY DOWNLOAD
VERY GOOD PRICE,
TRUE SATISFIED, THANKS
;
Genuine Toshiba owner's manual. Couldn't really ask for more. And written in understandable English in contrast to a few recent experiences I have had with manuals for other equipment other than Toshiba but made in China and written in "Chinglish"!
Connecting the Unit
Connecting the Power Terminal
� Always use the special red battery and ground wire [RD-223], which is sold separately. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body.
4. Connect the wires to the terminal.
� Fix the wires securely with the terminal screws. GND terminal Power terminal System remote control terminal System remote control wire Ground wire
3. Connect the speaker wires to the speaker output terminals.
� Connect the speaker wires, passing them through the terminal cover. � Fix the speaker wires securely with the terminal screws. Terminal screw
Using the Speaker Input
Connect the car stereo speaker output wires to the amplifier using the supplied speaker input connector.
� Do not connect both the RCA input and the speaker input at the same time.
Connecting the Speaker wires
The speaker output mode can be two-channel (stereo), one-channel (mono), or threechannel (stereo + mono). Connect the speaker leads to suit the mode according to the figures shown below.
� Do not connect both the RCA input and the speaker input at the same time.
Setting the Filter Constant
Three-channel mode, two-way system
Low-pass filter (for subwoofer/woofer): 6 dB/octave
L1 0dB �6dB
Band-pass filter (combination of low-pass filter and high-pass filter for midbass/mid): 6 dB/octave
L2 C2 0dB �6dB
1. Pass the battery wire from the engine compartment to the interior of the vehicle.
� After making all other connections to the amplifier, connect the battery wire terminal of the amplifier to the positive (+) terminal of the battery. Engine Fuse (30 A) compart- Interior of the vehicle ment
7 Connections when using the speaker input
C1
Mid-high (Right) Woofer (Mono) Mid-high (Left)
Two-channel mode (stereo)
Speaker output terminal Terminal cover Car Stereo
L1
fC
2fC
f fCL 2 fCL fCH 2fCH
C1
High-pass filter (for mid/mid-high): 6 dB/octave
C1 0dB �6dB
Three-channel mode, three-way system
Battery wire Speaker wire Speaker output (Right) Speaker (Left)
L2 C1 C2
Fuse (30 A) Positive terminal
High/mid-high (Right) Mid/mid-bass (Right) Woofer/subwoofer (Mono) Mid/mid-bass (Left) High/mid-high (Left)
Drill a 14 mm (1/2 inch) hole
Insert the O-ring rubber into the vehicle grommet into the vehicle body. body.
Connecting the Speaker Output Terminals
1. Expose the end of the speaker wires using nippers or a cutter by about 10 mm (3/8 inch) and twist.
Twist
fC 2
fC
f
4. Push on the terminal cover.
� A multi-channel system can be set up using a combination of filters. The inductance (L) and capacitance (C) will determine the frequency (fc) that the speaker will reproduce. Refer to the chart below to determine the components required. � Use the capacitors specified. Non-polarized capacitors rated at over ±25 V should be used for C1 and C2 in the diagram. Because of the voltage output of the amplifier, it is very important to use non-polarized capacitors rated at or over 25 V. This will prevent a safety hazard.
L1 C2
L2
2. Twist the battery wire, ground wire and system remote control wire.
Twist
10 mm (3/8 inch)
White/black: Left â� White: Left +
Gray/black: Right â� Gray: Right +
One-channel mode (mono)
C1
Component Guide
3. Attach lugs to wire ends. Lugs not supplied.
� Use pliers, etc., to crimp lugs to wires. Lug
2. Attach lugs to speaker wire ends. Lugs not supplied.
� Use pliers, etc., to crimp lugs to wires. Lug Speaker wire
Speaker input connector To speaker input terminal of this unit.
� Inductors (L1 and L2 in the diagrams) act as low-pass filters. Capacitors (C1 and C2 in the diagrams) act as high-pass filters. Inductors (L) are used for the woofer/subwoofer, and capacitors (C)
Speaker (Mono)
Speaker load Impedance
fc (Hz) 50 80 125 200 320 500 800 1,250 2,000 3,200 5,000 8,000 10,000 6.4 4.0 2.5 1.6 1.0 0.64 0.4 0.25 0.16 0.1 0.06 0.04 0.03
2�
L (mH) C (µF) 1,600 1,000 640 400 250 160 100 64 40 25 16 10 8 12.70 8.00 5.10 3.20 2.00 1.30 0.80 0.50 0.30 0.20 0.13 0.08 0.06
4�
L (mH) C (µF) 800.0 500.0 300.0 200.0 125.0 80.0 50.0 30.0 20.0 12.5 8.0 5.0 4.0
8�
L (mH) 25.50 16.00 10.00 6.40 4.00 2.60 1.60 1.00 0.64 0.40 0.26 0.16 0.13 C (µF) 400.0 250.0 160.0 100.0 62.0 40.0 25.0 16.0 10.0 6.2 4.0 2.5 2.0
are used for the high/mid-high. � Remember when bridging an amplifier it will see only half of the original speaker impedance. Therefore, you must use speakers that have ratings of 4 ohms or higher. If you use speakers that have lower impedance ratings it may cause damage to the amplifier. � When the inductors and capacitors are connected to the speaker wires, secure or solder them so they cannot be pulled loose. Tape or use heat shrink on the joints to prevent short circuits.
Ground wire Lug Battery wire
Three-channel mode (stereo + mono)
The power amplifier is basically a twochannel/one-channel bridgeable amplifier, but three channels can be achieved by combining the stereo and mono modes using inductors and capacitors.
|
|
|
> |
|
