|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This manual was very good & was very helpful with repairs.
Always great & fast service from Owner's manual.
;
Very pleased with the quality of the scan. No complaints whatsoever.
;
I liked the product. I would use their sevices again.
;
I Recently purchased yet another Service Manual from Owner-Manuals.com, this time for a Sony EVS700ES/UB Videocassette Recorder. The Manual was available for upload within two hours and is an Extremely Good copy, as some of this I was able to enlarge to get even better detail.
Once Again, Very happy with the result!
;
A good and useful manual. With these, We was abled to isolate and pin point the component that was causing the problem. The total time spent in troubleshooting is very much reduced.
CHAPTER 13 TROUBLESHOOTING
Code
Cause � The stapler shift motor (M10) is faulty. � The stapler shift home position sensor (PI7) is faulty. � The swing guide safety switch (MSW2) is faulty � The stapler safety switch (front; MSW8) is faulty. � The stapler safety switch (rear; MSW9) is faulty. � The swing motor (M8) is faulty. � The swing guide open sensor (PI16) is faulty.
Description � The stapler shift home position sensor does not turn off when the stapler shift motor has been driven for 4 sec. � The stapler shift home position is not detected when the stapler shift motor has been driven for 4 sec.
E532
E535
� The swing motor (M8) is faulty. � The swing guide closed sensor (P15) is faulty. � The tray B lift motor (M12) is faulty. � The tray B lock sensor (PI23) is faulty. � The tray B lower limit sensor (PI24) is faulty. � The tray B upper position sensor (PI20) is faulty. � The tray lower position sensor (PI21) is faulty.
� The swing guide closed sensor does not detect the swing guide when the swing motor has been driven for 2 sec. (detail code FF) � The swing guide closed sensor does not detect the swing guide when the swing motor has been driven for 2 sec. (detail code 01) � The lifter operation does not end within 25 sec after the tray lift motor has been driven. � The clock pulses from the tray idle rotation sensor are absent for 250 msec or more while the motor is rotating. � The input from the tray B upper position sensor (PI20) is '0' at power-on (i.e., the tray B is above the tray paper sensor PCB). � The power supply fan is at rest for 2 sec. � The paddle home position sensor does not detect the paddle for 5 sec after the motor has been started. � The tray auxiliary plate retraction sensor does not turn on within 2 sec after the motor has been started when the tray auxiliary plate is being retracted.
E542
E551 E577 E583
� The power supply fan (FM1) is faulty. � The paddle motor (M9) is faulty. � The paddle home position sensor (PI14) is faulty. � The tray auxiliary plate motor (M6) is faulty. � The tray auxiliary plate retraction sensor (PI11) is faulty.
n Resetting the Machine � If the copier is making copies, [1] The copier indicates an error code and the message "Turn On the Power Once Again." [2] After the jam reset mechanism has been activated, the copier runs a self check: if the result is good, the machine is reset; if not good, the machine enters down state* (indicated on the copier's control panel as "E5XX"). � If the copier is not making copies, [1] The copier indicates an error code and the message "Turn On the Power Once Again." [2] When the power has been turned off and then on, the copier runs a self check: if the result is good, the machine is reset; if not good, the machine enters down state* (indicated on the copier's control panel as "E5XX"). *State in which "E" is indicated.
13-260
COPYRIGHT © 1999 CANON INC.
CANON GP605/605V REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
|
|
|
> |
|