|
|
|
Who's Online
There currently are 6007 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I needed the manual immediately and I got it immediately. I couldn't find this manual anywhere else on the net. The site was easy to traverse, and the price was very reasonable. I'll definitely be back for any future needs.
 ;
I received a good service manual, with good resolution. Improve the instructions for the purchase because they are not well understood.
For the rest, so good.
Thanks Angel.
;
Very good documentation for the Grundig 2077 model (as well as similar 800/900/1000 series radios). The first two pages are a summary of reception specifications and output capability. The third page is the tuner dial indicator and dial cord routing diagram. the final ~5 pages are the schematics for the various models (including 2077). The scan quality of the schematics are good, adn can be easily read if zoomed in. The documents are in German, not English as stated. It would have been nice to have the tuning sequence and settings, and some trouble shooting materials... or component and wiring map.
;
Perfect like it was descriped, Perfect like it was descriped
;
Very good detail, all pages clear, exactly what I needed
<M2> UPPER ASS'Y(G)
C1 E
F 605 COVER(TOP/UPP)L COVER(TOP/UPP)R D1 C2 606 604 D2 J H C1 607 B 612 MONI.LOCK ASS'Y
611
MONITOR ASS'Y(G) (Refer to the Exploded view for this part.) 601 616 D1
SUB OPE UNIT
A
610 UPWARDS C2 U.CASE ASS'Y 602
(WR601a) F
617 PASTE
D2
FRAME(UPPER) ASS'Y E SOLDERING 2 POINT 603
G A 614 SCREW * SPEAKER 609 608 BRACKET(SPEAKER) * Mark*: This part was deleted on the way of production.
B
J H
G 613 CONCLUSION SCREW TORQUE TABLE PART.NO 611 ANOTHER SCREW TORQUE 0.2 ±0.01 N�m 0.08 ±0.01 N�m PROCESSING SUB OPE FPC. DRAWING FOR SPACER STICKING. 626 COVER(TOP/UPP)R COVER(TOP/UPP)L 615
VALLEY FOLDING VALLEY FOLDING MOUNTAIN FOLDING
UPPER ASS'Y(G) LYH20626
PROCESSING MONITOR FPC.
PROCESSING SUB OPE.
3 ±1 mm
VALLEY FOLDING AFTER PASTING SUB OPE PUSH TO THIS SLASH PART. MOUNTAIN FOLDING
SPACER(A)
DON'T STICK OUT SPACER IN SUB OPE FPC. VALLEY FOLDING
PASTE SPACERS NOT TO COVER THESE HOLES. STICK TO U.CASE. SHEET STICK ALONG THE REINFORCEMENT BOARD OF FPC. PASTE SPACER INSIDE BKT(UPPER). DON'T RUN A GROUND TO A LEVEL DIFFERENCE OF UPPER CASE. SOLDER 2 POINT MOUNTAIN FOLDING
SPACER(A) SPACER(A)
618 623
SHOULD BE COVERED THIS CONVEX.
SPACER(A) 620
DON'T STICK OUT SPACER IN UPPER CASE. LESS THAN 0.5mm
3 ±1 mm
STICKER
625
624 SPACER(A) 621
SPACER(A)
SHEET STICK ALONG THE CORNER OF FRAME. STICK FPC SO THAT THERE MAY BE NO CREVICE BET MEEN THE HOLE OF IT IN THE RIGHT SIDE OF THE HOLE RING.
PASTE SPACER THIS CONVEX IN UNDER SIDE. DON'T BE SEEN SPACER OUTSIDE OF UPPER CASE.
THE SIDE OF THE HOLE RING IS MET. THESE HOLES CAN BE SSEN.
619
DON'T RUN A GROUND OF UPPER CASE. DON'T SEPARATE.
SPACER(A) SHEET(SHIELD) 622
STICK SPACER THAT FPC MAY BE PRESSED DOWN.
Fig. 1-2-2c UPPER ASS�Y(G)
1-5
|
|
|
> |
|
