|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
HCD-GNX60/GNX70/GX9900
[VACS ON/OFF] � This mode is used to switch ON and OFF the VACS (Variable Attenuation Control System). Procedure: 1. Press ?/1 button to turn the set ON. 2. Press x button and [ILLUMINATION] button simultaneously. The message �VACS OFF� or �VACS ON� appears on the fluorescent indicator tube. [TUNER STEP CHANGE] � The step interval of AM channels can be toggled between 9 kHz and 10 kHz. Procedure: 1. Press ?/1 button to turn the set ON. 2. Press [TUNER/BAND] button repeatedly to select the �AM�. 3. Press ?/1 button to turn the set OFF. 4. Press [ENTER] button and ?/1 button simultaneously. The system will turn ON automatically. The message �AM 9k STEP� or AM 10k STEP� appears on the fluorescent indicator tube and thus the channel step is changed. [CD SERVICE MODE] � This mode let you move the CD sled motor freely. Use this mode when you want to clean the optical pick-up. Procedure: 1. Press ?/1 button to turn the set ON. 2. Select CD function. 3. Press x , [ENTER] button, and Z OPEN/CLOSE button simultaneously. 4. The CD service mode is activated. The message �SERVICE MODE� appears. 5. With the CD in stop status, turn m M knob to clockwise rotation to move the optical pick-up to outside track, or turn
[AGING MODE] This mode can be used for operation check of CD section. � If an error occurs, the aging operation would stops and the status is displayed. � If there are no error occurs, the aging operation would continues repeatedly. Procedure: 1. Press ?/1 button to turn the set ON 2. Select CD function. 3. Load three discs on the disc tray. 4. Press [PLAY MODE] button repeatedly to select the �ALL DISCS� mode, and press the [REPEAT] button repeatedly to select �REPEAT OFF� mode. 5. Press x button, [ENTER] button, and [EX-CHANGE/DISC SKIP] button simultaneously. 6. Aging operation is started. 7. To release this mode, press ?/1 button or disconnect the power cord to turn the power OFF. Aging mode sequence:
Start (from disc 1)
Disc chucking
TOC reading
Play first track for 2 seconds
Play last track for 2 seconds EX-CHANGE open/close
m M knob to counterclockwise rotation to move to
inside track. The message �SLED OUT� or �SLED IN� appears on the fluorescent indicator tube. 6. To turn on or off the laser, press [DIRECTION] button. The message �LASER ON� or �LASER OFF� appears on the fluorescent indicator tube. 7. To release this mode, press ?/1 button.
Open the disc tray Disc skip
Close the disk tray
Change the next disc
18
|
|
|
> |
|
