|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
TUNER SECTION
0 dB=1µV
AM Tuning Voltage Adjustment
Main board TP1 F G VT DC voltmeter
+ �
Procedure: 1. Set the reception frequency of the unit to 530 kHz. 2. Adjust L105 for 1.2 ± 0.05 V reading on the DC voltmeter. 3. Set the reception frequency of the unit to 1,710 kHz. 4. Confirm that the voltage reading on the DC voltmeter is within 8.0 ± 0.5 V. Adjustment Location: MAIN board (See page 14) AM Tracking Adjustment
loop antenna loop antenna (Supplied accessories)
AM RF SSG set 30% amplitude modulation by 400 Hz signal AM ANTENNA terminal (TM1)
60 cm
Field strength dB (µV/m) =SSG output level dB (µV/m) �26 dB.
Procedure: 1. Tune the set to 600 kHz. 2. Set the output of AM RF SSG so that the input level of the set will become 60 dB (µV/m). 3. Adjust L104 so that when the waveform on the oscilloscope is maximum, no noise appears. 4. Tune the set to 1,400 kHz.
5.
Adjust TC102 so that when the waveform on the oscilloscope is maximum, no noise appears.
� Repeat the procedures in each adjustment several times, and the tracking adjustment should be finally done by the trimmer capacitors. Adjustment Location: MAIN board (See page 14)
FM Tuning Voltage Adjustment (US, Australian, Mexican model)
Main board TP1 IF G VT DC voltmeter
+ �
Procedure : 1. Set the reception frequency of the unit to 87.5 MHz. 2. Adjust L103 for 1.2 ± 0.05V reading on the DC voltmeter. 3. Set the reception frequency of the unit to 108 MHz. 4. Confirm that the voltage reading on the DC voltmeter is within 7.8 ± 0.5V. Adjustment Location: MAIN board (See page 14)
� 13 �
|
|
|
> |
|
