PHILIPS HD4638/10
Owner's Manual

ENGLISH
Introduction
.

4222 001 97392 Using the appliance 1 Open the lid. 2 Fill the kettle with water (fig. 3). You can fill the kettle either through the spout or through the open lid. 3 Close the lid. Make sure that the lid is properly closed to prevent the kettle from boiling dry. 4 Place the kettle on its base, put the plug in the wall socket. � � � � � � HD4628 and HD4626: Set the on/off switch to 'I' (fig. 4). HD4638: Set the on/off switch to 'I' (fig. 5). HD4646: Set the on/off switch to 'I' (fig. 6). The kettle starts heating up. The kettle automatically switches off ('O' position) when the water has reached boiling point. You can interrupt the boiling process by setting the on/off switch to 'O'. Cleaning and descaling
. .

Congratulations on acquiring your new Philips kettle! In these instructions for use you will find all the information you need to optimally enjoy your kettle for a long time. General description (fig. 1)
.

A On/off switch (I/O) B Lid C Spout D Water level indicator E Base F Scale filter (HD4646/HD4628 only) Important
.

Read these instructions for use carefully before using the appliance and save them for future reference. � � � � � � � � � � � � � � � � � � Check if the voltage indicated on the base of the kettle corresponds to the local mains voltage before you connect the appliance. Only use the kettle in combination with its original base. Always place the base and the kettle on a dry, flat and stable surface. Keep the appliance and its cord out of the reach of children. Do not let the mains cord hang over the edge of the table or worktop. Excess cord can be stored in the base of the appliance. Keep the cord, the base and the kettle away from hot surfaces. Do not use the appliance if the mains cord, the plug, the base or the kettle itself is damaged. If the mains cord is damaged, it must always be replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard. Do not immerse the kettle or the base in water or any other liquid. The kettle is only meant for boiling water. Do not use it to heat up soup or other liquids or jarred, bottled or tinned food. Boiling water can cause serious burns. Be careful when the kettle contains hot water. Never fill the kettle beyond the maximum level indication. If the kettle has been overfilled, boiling water may be ejected from the spout and cause scalding. Do not open the lid while the water is boiling. Be careful when you open the lid immediately after the water has boiled: the steam coming out of the kettle is very hot. Avoid touching the body of the kettle, as it gets very hot during use. Always lift the kettle by its handle. HD4646 only: Always make sure the water in the kettle at least covers the bottom of the kettle to prevent the kettle from boiling dry. HD4638/HD4628/HD4626 only: Never fill the kettle below the minimum level to prevent the kettle from boiling dry. Some condensation may appear on the base of the kettle. This is perfectly normal and does not mean that the kettle has any defects. Depending on the hardness of the water in your area, small spots may appear on the heating element of your kettle when you use it. This phenomenon is the result of scale build-up on the heating element and on the inside of the kettle over time. The harder the water, the faster scale will build up. Scale can occur in different colours. Although scale is harmless, too much scale can influence the performance of your kettle. Descale your kettle regularly by following the instructions given in the chapter 'Cleaning and descaling'.

Always unplug the appliance before cleaning it. Do not use any abrasive cleaning agents, scourers etc. to clean the appliance. Never immerse the kettle or its base in water. Cleaning the kettle 1 Clean the outside of the kettle with a soft, damp cloth moistened with warm water and some mild cleaning agent. Cleaning the filter (HD4646/HD4628 only) Scale is not harmful to your health but it may give your drink a powdery taste. The scale filter prevents scale particles from ending up in your drink. Clean the scale filter regularly. 1 The filter can be cleaned in three ways: � � � by taking it out of the kettle (1) and gently brushing the filter with a soft nylon brush under a running tap (2) (fig. 7). by leaving it in the kettle when descaling the whole appliance. in the dishwasher.

Descaling the kettle Regular descaling will prolong the life of the kettle. In case of normal use (up to 5 times a day), the following descaling frequency is recommended: - Once every 3 months for soft water areas (up to 18 dH). - Once every month for hard water areas (more than 18 dH). 1 Fill the kettle with water up to three-quarters of the maximum level and bring the water to the boil. 2 After the kettle has switched off, add white vinegar (8% acetic acid) to the maximum level. 3 Leave the solution in the kettle overnight. 4 Empty the kettle and rinse the inside thoroughly. 5 Fill the kettle with clean water and boil the water. 6 Empty the kettle and rinse it with clean water again. � Repeat the procedure if there is still some scale in the kettle.

Boil-dry protection This kettle is equipped with boil-dry protection. This device will automatically switch the kettle off if it is accidentally switched on when there is no water or not enough water in it. The on/off switch will stay in 'on' position. Set the on/off switch to 'off' and let the kettle cool down for 10 minutes. Then lift the kettle from its base to reset the boil-dry protection. The kettle is now ready for use again. Before first use � � � �
.

You can also use an appropriate descaler. In that case, follow the instructions on the package of the descaler. Replacement
.

Replacement filters for your kettle can be purchased from your Philips dealer or a Philips service centre. The table below indicates which filters are suitable for your kettle. If the kettle, the base or the mains cord of the appliance is damaged, take the base or the kettle to a service centre authorised by Philips for repair or replacement of the cord to avoid a hazard. Environment �
.

Remove stickers, if any, from the base or kettle. Place the base on a dry, stable and flat surface. HD4646 only: You can adjust the length of the cord by winding it round the reel in the base (fig. 2). Pass the cord through one of the slots in the base.

Before using the kettle for the first time: 1 Rinse the kettle with water. 2 Fill the kettle with water up to the maximum level and let it boil once (see 'Using the appliance'). 3 Pour out the hot water and rinse the kettle once more.

Do not throw the appliance away with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this you will help to preserve the environment (fig. 8).

2/7