PHILIPS HQ804/16
Owner's Manual

english
important Read this user manual carefully before you use the appliance and save it for future reference. -

5 Brush the hair chamber (Fig. 10). 6 Put the shaving unit back onto the shaver. every two months: shaving heads Note: Do not use cleaning agents or alcohol to clean the shaving heads. Only use the HQ110 Shaving Head Cleaning Spray. 1 Switch off the shaver. 2 Remove the shaving unit (Fig. 8). 3 Turn the wheel anticlockwise (1) and remove the retaining frame (2) (Fig. 11). 4 Remove the shaving heads from the shaving unit one by one (Fig. 12). Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. 5 Remove the cutter from the guard (Fig. 13). 6 Clean the cutter with the short-bristled side of the brush (Fig. 14). 7 Brush the guard (Fig. 15). 8 Put the shaving heads back into the shaving unit. 9 Put the retaining frame back into the shaving unit and turn the wheel clockwise. 10 Put the shaving unit back onto the shaver. Tip: For optimal shaving performance, we advise you to lubricate the shaving heads with a drop of sewing machine oil every six months. storage Put the protection cap on the shaver after use to prevent damage to the shaving heads (Fig. 6).

Troubleshooting Problem The shaver doesn�t shave as well as it used to. Solution You may not have cleaned the appliance properly. Clean the shaving heads thoroughly (see chapter �Cleaning and maintenance�). Long hairs may be obstructing the shaving heads. Clean the cutters and guards properly with the brush supplied (see chapter �Cleaning and maintenance�). The shaving heads may be damaged or worn. Replace the shaving heads (see chapter �Replacement�). The batteries may be running low. Replace the batteries (see chapter �Preparing for use�). The shaver doesn�t switch on when I push the on/off slide upwards. The batteries may be empty. Replace the batteries (see chapter �Preparing for use�).

Warning

-

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

-

Caution

Use and store the appliance at a temperature between 5°C and 35°C. This shaver is not waterproof and cannot be cleaned under the tap. Keep the shaver dry (Fig. 1). Remove the batteries from the appliance if you are not going to use it for quite some time.

Compliance with standards

This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. Preparing for use

You may have inserted the batteries incorrectly. Insert the batteries correctly into the battery compartment. Make sure the + and - poles point in the right direction.

The appliance runs on two R6 AA 1.5-volt alkaline batteries. We strongly advise you to use Philips Powerlife batteries. They supply sufficient energy for up to 60 minutes of shaving. inserting batteries 1 Remove the lid of the battery compartment (Fig. 2). 2 Put two batteries in the battery compartment (Fig. 3). Make sure your hands and the appliance are dry when you insert the batteries. , Make sure the + and - poles of the batteries point in the right direction

Replacement Replace the shaving heads every two years for optimal shaving results. Replace damaged or worn shaving heads with HQ4+ Philips Micro+ Lift & Cut Shaving Heads. 1 Switch off the shaver. 2 Remove the shaving unit (Fig. 8). 3 Turn the wheel anticlockwise (1) and remove the retaining frame (2) (Fig. 11). 4 Remove the shaving heads from the shaving unit and replace them with new ones (Fig. 12). 5 Put the retaining frame back into the shaving unit and turn the wheel clockwise. 6 Put the shaving unit back onto the shaver. Accessories The following accessories are available: - HQ4+ Philips Micro+ Lift & Cut Shaving Heads - HQ110 Philips Shaving Head Cleaning Spray (not available in some countries) environment Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment (Fig. 16). Batteries contain substances that may pollute the environment. Do not throw away empty batteries with the normal household waste, but dispose of them at an official collection point for batteries. Always remove the batteries before you discard and hand in the appliance at an official collection point. guarantee & service If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Customer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, go to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV. 2/5

Note:The appliance does not work if the batteries have been placed incorrectly. 3 Put the lid of the battery compartment back onto the appliance (�click�).

-

Avoiding damage due to battery leakage

Remove the batteries if you are not going to use the appliance for a month or more. Do not leave empty batteries in the appliance.

Using the appliance 1 Remove the protection cap. 2 Push the on/off slide upwards to switch on the shaver (Fig. 4). 3 Move the shaving heads quickly over your skin. Make both straight and circular movements (Fig. 5). Note: Shaving on a dry face gives the best results. Note:Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system. 4 Push the on/off slide downwards to switch off the shaver. 5 Put the protection cap on the shaver to prevent damage to the shaving heads (Fig. 6). Cleaning and maintenance Regular cleaning guarantees better shaving performance. every week: shaving unit and hair chamber 1 Switch off the shaver. 2 Brush the outside of the shaving unit with the brush supplied (Fig. 7). 3 Remove the shaving unit (Fig. 8). 4 Brush the inside of the shaving unit (Fig. 9). 4222.002.4942.1

-