|
|
|
Who's Online
There currently are 5850 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was complete and of great quality. Originally a tri-lingual file, I first received only one language. After a note to owners-manuals.com, I quickly received the remaining languages... Great service, definitely worth it.
;
Thank you for providing this manual and at low cost.
The Philips scope is of excellent quality, longevity and build and had a couple of faults
when it was passed to me. Having the CCT diagrams is a blessing.
I have fixed the problems and also modded the scope to my requirements.
I have built a 24v Li-Ion pack for portable use from old but good laptop batts.
it is working beautifully and I am well pleased. Keep up the good work Guys.
 ;
manual was very helpful in learning how to propery use my washer. I could not find this manual anywhere else.
;
Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
EN
TIMER RECORDING
SYMPTOM
1. Timer recording won�t work.
57
POSSIBLE CAUSE
� The clock and/or the timer have been set incorrectly. � The timer is not engaged. � Timer recording is in progress.
CORRECTIVE ACTION
Re-perform the clock and/or timer settings. Press � and confirm that ��� is displayed on the display panel. Timer programming can�t be performed while a timer recording is in progress. Wait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape. Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the Record Safety tab intact. Check the programmed data and reprogram as necessary, then press � again. The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. Refer to "Guide Program Number Set" and re-perform the procedure ( pg. 53).
2. Timer programming is not possible.
3. ��� and �]� on the display panel won�t stop blinking. 4. The cassette is automatically ejected, and ��� and �]� on the display panel won�t stop blinking. 5. ��� blinks for 10 seconds and the Timer mode is disengaged.
� The timer is engaged but there�s no cassette loaded. � The loaded cassette has had its Record Safety tab removed.
� � has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly. � The end of the tape was reached during timer recording.
6. The cassette is automatically ejected, the power shuts off and ��� and �]� won�t stop blinking. 7. SHOWVIEW does not timer-record properly.
� The recorder�s channel positions have been set incorrectly.
OTHER PROBLEMS
SYMPTOM
1. Whistling or howling is heard from the TV during camcorder recording. 2. When scanning channels, some of them are skipped over.
POSSIBLE CAUSE
� The camcorder�s microphone is too close to the TV. � The TV�s volume is too high. � Those channels have been designated to be skipped.
CORRECTIVE ACTION
Position the camcorder so its microphone is away from the TV. Turn the TV�s volume down. If you need the skipped channels, restore them ( pg. 48).
3. The channel cannot be changed.
� Recording is in progress.
Press PAUSE to pause the recording, change channels, then press PLAY to resume recording. Perform manual setting again.
4. Channel settings that were made manually seem to have changed or disappeared. 5. No channels are stored in the recorder's memory.
� After the manual settings were made, Auto Channel Set was performed. � The TV aerial cable was not connected to the recorder when Auto Set Up was performed.
Connect the TV aerial cable to the recorder properly and turn off the recorder power once, then turn the recorder power back on again. The recorder will try Auto Set Up again ( pg. 4). Re-set the remote control to the correct brand ( pg. 34, 35).
6. The remote control won�t operate the TV or satellite tuner.
� The remote control brand setting is incorrect.
|
|
|
> |
|
