JVC HRS5912U
Owner's Manual

Timer Recording
Up to 8 timer recording programs can be made using VCR Plus+ timer programing, Express timer programing or 24HR Quick Programing method as far as a year in advance. Remember, the clock must be set before you can program the timer. Turn on the VCR and TV, and select the VCR channel (or AV mode).

VCR Plus+® Timer Programing
The PlusCode programing numbers are the numbers next to the program in most TV listing. Load a cassette with the record safety tab intact. The VCR turns on, and the counter is reset, automatically.

A Press PROG. on the Remote to access
the PlusCode No. screen.
PLUSCODE NO.

NOTES:

� If all the 8 programs have already been set, �PROGRAM FULL� appears on the TV screen. � After timer recording is completed, the VCR turns off automatically. � You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded. � To timer-record cable or satellite channels, perform �Cable Box and/or DBS Receiver Control Setting� ( pg. 7) and be sure to keep the cable box or DBS receiver turned on. � Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time, channel settings, and other menu settings are lost. As a result, when the power is supplied again to this VCR after the power failure, this VCR starts the Plug&Play setting automatically to restore the clock time and channel setting. If the clock time and channel setting are restored correctly, each timer program you have made will start at its start time unless its end time has elapsed. � If the tape reaches its end during timer recording, the recording stops and �#�, � � and � $� on the display panel blink. Press TIMER to disengage timer, then press STOP/EJECT (0) on the VCR to eject the cassette or press POWER 1 then press REW (3) on the Remote to rewind the tape.

PRESS NUMBER KEY (0�9) PRESS (+/�) TO SET EXPRESS PROGRAMMING PRESS (PROG.) TO END

B Press the appropriate Number keys

to input the PlusCode number, then press OK or e. Check to make sure the setting is accurate on the Program screen.
PLUSCODE NO. 12345678
PROGRAM 1 (PLUSCODE NO. 12345678) START STOP 8:00PM 10:00PM DATE CH 12/24/03 12 SP WED PRESS (8=DAILY, 9=WEEKLY STOP+/� = STOP TIME, SP/EP) PRESS (PROG.) TO END

PRESS NUMBER KEY (0�9) THEN (OK) PRESS (PROG.) TO END

Changing VCR Plus+® Setting
The VCR Plus+ programing system assigns a VCR Plus+ guide channel to the TV channels and the cable channels. These guide channel numbers are also called the VCR Plus+ channel codes. Most TV listings have a section, usually a chart, indicating the guide channel numbers assigned to each station. To ensure that VCR Plus+ timer recording operates correctly, it is necessary to set the VCR Plus+ �Guide Channel Set� for each station. If you have moved to a different area or if a broadcasting station�s channel number has been changed, perform the following steps to set the correct guide channel number.

� If the Guide Channel Set screen GUIDE CHANNEL SET appears after pressing OK, press the GUIDE CH : 12 Number keys, CH+/� or rt to input VCR CH : � � � the number of the channel on which the broadcast for the PlusCode PRESS NUMBER KEY (0�9) number is received on the VCR or OR ( , ), THEN (OK) PRESS (PROG.) TO END cable box, then press OK. � To set the tape speed, press SP/EP. � To change the stop time, press STOP+/�. � To timer-record daily (Monday�Friday) or weekly serials, press DAILY (M-F) (Number key �8�) or WEEKLY (Number key �9�). Pressing the button again makes the �DAILY� or �WEEKLY� display disappear. � If you made a mistake, press CANCEL to access the PlusCode No. screen again. � If an incorrect PlusCode number or the one for a broadcast already finished has been inputted, �ERROR� is displayed for about 5 seconds, then the PlusCode No. screen reappears.

C Press OK or PROG.. D

A Access Main Menu screen, then Initial Set screen
Press MENU on the Remote. Press rt to move the highlight bar (arrow) to �INITIAL SET�, then press OK or e.

� If �PROGRAM NOT COMPLETED PROGRAM OVERLAP� appears, see �Program overlap warning display� ( pg. 14). Press TIMER. The VCR turns off automatically and �#� is displayed on the display panel.

B Access Guide Channel Set screen
Press rt to move the highlight bar (arrow) to �GUIDE CHANNEL SET�, then press OK or e.

C Input guide channel number
Press rt or the Number keys to select the VCR Plus+ guide channel number as shown in the TV listing, then press OK or

GUIDE CHANNEL SET GUIDE CH : 6 VCR CH : � � �

e.

PRESS NUMBER KEY (0�9) OR ( , ), THEN (OK) PRESS (MENU) TO END GUIDE CHANNEL SET GUIDE CH : VCR CH : 6 47

D Input receiving channel number
Press rt or the Number keys to select the number of the channel on which the guide channel�s broadcasts are received, then press OK or e. � Repeat steps 3 and 4 for each instance.

PRESS NUMBER KEY (0�9) OR ( , ), THEN (OK) PRESS (MENU) TO END

E Return to normal screen
Press MENU on the Remote. CONTINUED ON NEXT PAGE � 12 �