|
|
|
Who's Online
There currently are 5422 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I needed the manual immediately and I got it immediately. I couldn't find this manual anywhere else on the net. The site was easy to traverse, and the price was very reasonable. I'll definitely be back for any future needs.
 ;
I received a good service manual, with good resolution. Improve the instructions for the purchase because they are not well understood.
For the rest, so good.
Thanks Angel.
;
Very good documentation for the Grundig 2077 model (as well as similar 800/900/1000 series radios). The first two pages are a summary of reception specifications and output capability. The third page is the tuner dial indicator and dial cord routing diagram. the final ~5 pages are the schematics for the various models (including 2077). The scan quality of the schematics are good, adn can be easily read if zoomed in. The documents are in German, not English as stated. It would have been nice to have the tuning sequence and settings, and some trouble shooting materials... or component and wiring map.
;
Perfect like it was descriped, Perfect like it was descriped
;
Very good detail, all pages clear, exactly what I needed
ICF-CD863/CD863L
Adjustment Location:
� MAIN BOARD (Component Side) �
AUTO BRIGHTNESS ADJUSTMENT Connecting:
digital voltmeter LCD board TP (DIMMER) TP (GND) 100 k � + �
CD SECTION
CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias.
FOCUS BIAS CHECK
1. Connect the oscilloscope to TP (RF) and TP (GND) on the CD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3. Press the u (CD) button. 4. Confirm that the oscilloscope waveform is as shown in the figure below. (eye pattern) A good eye pattern means that the diamond shape (�) in the center of the waveform can be clearly distinguished. � RF signal reference waveform (eye pattern)
VOLT/DIV: 0.2 V (with the 10: 1 probe in use.) TIME/DIV: 500 ns
CT4 LW VCO Voltage Adjustment (CD863L) L4 AM (MW) VCO Voltage Adjustment RV1 FM Stereo Adjustment L1 FM RF CT2 Tracking Adjustment
}
T1 AM IF Adjustment
1. Set to power off state. 2. Connect a digital voltmeter to TP (DIMMER) and TP (GND) on the LCD board and confirm that the voltage is 0 V. 3. Turn on the power. 4. Connect the digital voltmeter to TP (DIMMER) and TP (GND) on the LCD board and adjust RV401 so that the voltage becomes 1.5 ± 0.05 V. 5. Turn off the power. 6. Applied sufficient light to IC403 (brightness sensor) on the DIMMER board and confirm that the voltage is 3.3 ± 0.3 V. 7. Short the BP404. Adjustment Location: � LCD BOARD (Component Side) �
0.8 ± 0.2 Vp-p
L3-1 AM (MW) Tracking CT2 Adjustment
}
L3-2 LW Tracking Adjustment CT3 (CD863L)
}
When observing the eye pattern, set the oscilloscope for AC range and raise vertical sensitivity.
Adjustment Location:
� MAIN BOARD (Conductor Side) �
TP (FM IN)
RV401 Auto Brightness Adjustment
� CD BOARD (Conductor Side) �
TP (GND) TP (VT) TP (FM ST)
IC701
� LCD BOARD (Conductor Side) �
TP (GND)
TP (RADIO B+)
TP (GND)
TP (RF)
1 4 CN303
TP (DIMMER)
� DIMMER BOARD (Conductor Side) �
IC403
13
13
|
|
|
> |
|
