This was a hard to find manual. When I did find it , some sites wanted way too much for the file.
Owner-manual .com had it for a really reasonable price. Not only that but it was sent very quickly and was a quality scanned document, unlike some others I purchased from a different site.
Good job guys!!
Larry
Fast and courteous service. Product delivered as described. Thank you.
Text excerpt from page 3 (click to view)
Suggestions for the installation and use of the hood
� The horizontal sections of the pipe must be slanted slightly upwards (about 10%) to ensure an easy flow of the air outwards. � The best performance of the unit is obtained in the external exhaust model (suction), therefore in the limits of the possibilities it is advised to use the external exhaust (suction) type. � The best performances are obtained with short pipes (max. 4 m) and with few curves.
Using the hood
The hoods JDU 2320 and JDU 2321 are supplied with a three speed motor. To get best efficiency, we suggest to use slow speeds in normal conditions and the highest in particular cases of strong smell and vapour concentration. It is advisable to switch on the extractor hood a few minutes before starting cooking and then to leave it running for approximately 15 minutes afterwards to ensure that all odours are extracted.
Rectangular carbon filter
This is neither washable nor re-usable and must be replaced every 6-8 months. To fit it, fix it to the frame G using the buttons N. To remove it, move the clamps N inwards and pull it downwards (fig. 4).
Attention
Failure to observe the rules for cleaning the appliance and changing and cleaning the filters may cause fires. Therefore, we recommend observing these instructions.
Electric connection
Before completing any connection, make sure the house voltage corresponds with the voltage indicated on the label affixed inside the hood. The hood is supplied with a standard plug; connect it to a correspondingly standard socket. In the case is intended to connect the appliance permanently to the mains after having removed the plug supplied, must be fitted a two-pole switch conforming to regulations with an opening distance between contacts of not less than 3mm The manufacturers are not liable for any problems caused by the user�s failure to observe the above instructions.
Maintenance
Before performing any maintenance operation, disconnect the hood from the electricity.
Changing the bulbs
� Disconnect the hood from the electricity. � Remove the grate. � Always replace burn-out bulbs with oliveshaped max 40 Watt (E14) bulbs. � Before calling for repair service because the hood fails to light up, make sure the bulbs are screwed in tightly.
Grease filter
The hood has a metal grease filter. To clean the filter, proceed as follows: � Open the grill using the bolts L. � Remove the grill completely (pull the right side of the grill forward and unhook it from the slots to which it is attached. � With normal use, the grease filter should be washed once a month in a dishwasher or in warm soapy water and should be left to dry before being refitted. � When the filters are washed, the grid should also be cleaned with warm water and biodegradable detergent.
Cleaning
To clean the outside of the hood use a cloth moistened with denatured alcohol or neutral liquid detergents. Never use products containing abrasives. This appliance meets 87/308 EWG radio and television noise standards.
Fixing to the cabinet
� Make holes at the bottom of the cabinet using the template supplied. � Fit the four 4.2x35 screws supplied, from inside the cabinet in the holes on the appliance (fig. 5).
Only for hood model JDU 2321
A thin synthetic filter may be used as an alternative to the metal filter. This filter should be replaced when the colouring of the upper part shows on the bottom part.
Fixing to the wall
� Fit the template to the wall. � Make three 8 mm � holes on the wall. Two on H, and one hole on any of points I, as required. � Fit three 8 mm wall plugs. � Fit two 5x45 screws on H�do not tighten completely. � Now hang the hood (holes H). Tighten the two screws and fit the third 5x45 screw in hole I from inside the cabinet (fig. 6).
