|
Who's Online
There currently are 5852 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
The AKAI 1720 model reel to reel tape recorder described in this Manual is quite an old unit - circa late 1960's. As a consequence, the description of the mechanical details - and adjustments thereof - is quite critical. The manual does this quite well. The schematics are also well presented and have detailed PCB overlays. Probably the only negative is that some half-tone detail has been lost from the original manual as it has been scanned in simple B&W.
;
Perfect source for service manuals: fast and professional transaction; high quality, perfect readable and largely scaleable PDF; complete schemes, diagrams and spare part list. Tnx a lot, cu again!!!!
;
I got your link from a friend and I must say that I am really satisfied with your service. Specially this B&O manual I didn't find anywhere on the web... but you could deliver it :-) . You deliver very fast and the copy is of good quality. So your webpage is bookmarked. Thanks
;
This was the Sony CCU-500A Service manual I was looking for.
The price was reasonable.
The permission to download was quck.
I will use Owner-Manual.com for all my manual needs.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
Technical Manual
K2 S9800/K2 S9800SE
EXPLODED VIEW
8 10 26 19 6 40 9
35
39
33
27
5
20
31
38
18
35
37
25 1
17
4
23 30 15 35
12 13 14
24
34 16 2 29
3 11 36 7 22 41 28 21 32
TO SERVICE THE K2 S9800 The crossover network, after removal of the (6) faceplate screws, should extract far enough out of the cabinet for service without wire or driver removal. Access to 9V bias batteries � metal plate removed by two thumbscrews on the network faceplate. Replacement or service of the high-frequency drivers requires access through the woofer opening, following these steps: NOTE: IT IS RECOMMENDED TWO PERSONS BE INVOLVED IN K2S9800 DISASSEMBLY 1) Lay the loudspeaker down, on its back (drivers facing up), on a padded surface. 2) Remove the grille. 3) Remove the (8) Phillips woofer screws. 4) The woofer is best extracted by inserting two 1/4 x 20 (3" or longer) threaded machine screws into opposite sides of the two threaded woofer screw openings. Caution: Only two of the holes are threaded; they should be the top and bottom holes in the woofer frame. Thread
the bolts into the openings by hand, then pull upwards, lifting the woofer from the counterbore. Then, while one person supports the woofer, another can remove both connecting wires from the terminals. Set the woofer aside. 5) Inside the cabinet, at the bottom of the HF horn, are the three mounting screws; remove them. 6) The HF horn can now be removed from the cabinet by reaching in and pushing the assembly out; remove both connecting wires from the terminals. Set the HF assembly/horn aside. 7) The (10) screws holding the top cap assembly are now exposed; remove them. 8) Lift the top cap assembly with UHF assembly off the cabinet. NOTE: a) When replacing the HF horn, to assist the (3) screw holes in lining up properly, one person may have to depress the gasket by pressing the horn assembly down into the cabinet, while the other replaces the screws. b) Remember to observe correct polarity when reattaching all driver wires.
JBL Consumer Products, 250 Crossways Park Drive, Woodbury, New York 11797 4
7/04
K2 S9800/K2 S9800SE
|
|
|
> |
|