|
|
|
Who's Online
There currently are 5171 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very satisfied with received document, all is right, Thank You very much, it was a Pleasure to work with You.
 ;
great site, the most easy and fastest way to find the manual you need, no 5 star because the manual was only available in german, but I speak german as well so no problem for me.
;
thanks for this download i got a pioneer bdp-lx70a blu-ray player and it had no manual i search everywhere on the internet and came across owner-manuals.com and i found that it was so easy to find and downloaded from this site if i ever need a manual again this would be the first place that i would come too thanks guys
;
Superb! It's the original manual. We can now use our old calculator with its full function.
;
This is a very well written and comprehensive manual. It answered all our queries.
To select the subwoofer cutoff frequency � WooferFreq (only for KD-LX333)
When a subwoofer is connected to this unit, select an appropriate cutoff frequency level for your subwoofer. When shipped from the factory, the subwoofer cutoff frequency is set to �FREQ MID.� � FREQ LOW: Frequencies higher than 50 Hz are cut off to the subwoofer. � FREQ MID: Frequencies higher than 80 Hz are cut off to the subwoofer. Frequencies higher than 120 Hz are cut off to the subwoofer.
To adjust the line input level � LINE ADJ
(only for KD-LX333)
Adjust the line input level properly when an external component is connected to the LINE INPUT plugs. When shipped from the factory, the line input level is set at level �00.� If the input level of the connected component is not high enough, increase the input level properly. Without adjusting the line input level, you may be surprised at a loud sound when you change from the external component to another source.
� FREQ HIGH:
To select the external component to use �� EXT INPUT (only for KD-LX111)
You can connect the external component to the CD changer jack on the rear using the Line Input Adaptor KS-U57 (not supplied). To use the external component as the playback source through this unit, you need to select which component � CD changer or external component � to use. When shipped from the factory, CD changer is selected as the external component. To use the external component other than CD changer. � CD CHANGER:To use the CD changer. � LINE INPUT:
To change the AM/FM channel intervals � AREA
When this unit is shipped from the factory, the channel intervals are set to 10 kHz for AM and 200 kHz for FM (AREA US settings). You will have to change the channel intervals when using this unit in an area other than North America and South America. � AREA EU: Select this when using this unit in an area other than North and South America. (9 kHz for AM and 50 kHz (for manual tuning) / 100 kHz (for searching) for FM) Select this when using this unit in North or South America. (10 kHz for AM and 200 kHz for FM)
Note: For connecting the Line Input Adaptor KS-U57 and the external component, refer to the Installation/ Connection Manual (separate volume).
� AREA US:
To make the front panel look flat (hiding the control panel) � FLAT PANEL
When operating the receiver using the remote control, you can hide the control panel to make the front panel look flat. When shipped from the factory, �FLAT OFF� is selected. � FLAT ON: The control panel will not come out when you turn on the unit. To use the control panel, press 4 so that the control panel comes out. If no operation is done for about 10 seconds, it automatically goes back into the receiver. You can use the control panel normally.
Note: If the channel intervals settings are changed, the following will occur. � The names assigned to the stations will be erased from memory. To reassign the names, see
�Assigning names to the sources� on pages 23 and 24.
� FLAT OFF:
Note: When �FLAT ON� is selected, you can eject a CD by holding 4 .
21
ENGLISH
|
|
|
> |
|
