|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a high quality manual with clear schematic and components layout diagrams ; with service procedure included.
 ;
This service manual for the Kenwood KT-990D was reproduced really well ,is very legible and manual is complete.Combined with the low price paid,in the future,I will be checking Owner-Manuals.com any time I need a manual.
;
When I purchased this manual I had my doubts regarding the quality as the price was so reasonable as compared to other outlets.
The manual itself is of high standard the print is very clear as are the diagrams. Obviously with the diagrams one has to zoom in otherwise it is to small to be able to read.
Overall I am very pleased with the company who delivered as they said and with the manual they supplied.
I occasionally require a manual and now having registered with this company I shall order from them in the future.
;
I was at first dubious about payiong for downloaded manuals but having done so, I was extremely impressed with quality of the two manual I ordered, well worth the small price I paid.
I would highly recommend these to my friends.
;
reasonable price for the schematic - the service is perfect, all as expected and pointed by instructions - good scan of the original plans - thank you!
MD-MT180H
Error Messages
ERROR MESSAGES BATT EMPTY BLANK MD MEANING q The battery has run down. q Nothing is recorded. (Replace the disc with a recorded disc.) Can't COPY q You tried to record from a copy prohibited MiniDisc. (Record using the analogue cable.) q You tried to record signals other than music (such as data). Can't EDIT q A track cannot be edited. (Change the stop position of the track and then edit it.) Can't PLAY q You tried to play back a track that cannot be played with this equipment. HOLD LOCKED DISC FULL Er-MD (**) Can'tWRITE DEFECT! ERROR MESSAGES Can'tSTAMP MEANING q Stamp function does not work. (Check the number of tracks.) q Cannot save the TOC information correctly to a MiniDisc. q The disc is scratched. (If the recorded sound is not right, retry recording or replace the disc with a recordable one.) q The disc is out of recording space. q The microprocessor has reported a system fault and the unit is out of order. (To have it repaired, go to the distributor where you purchased the unit.) q The unit is in the hold mode. q You removed a MiniDisc whilst recording or editing. (Turn off the power before removing the MiniDisc.) NO DISC q A disc has not been loaded.
Can't READ (*) q The disc data cannot be read because the disc is damaged. (Reload the Minidisc or replace it with another one.) Can't REC q Recording cannot be performed correctly due to vibration or shock.
Num ber or symb ol appears in (*) posit ion.
ERROR MESSAGES NO SIGNAL
MEANING q Poor connection of the digital cable. q No output signal comes out from the connected unit to playback. (Use the AC power for the connected unit.) q The input signal has improper sampling frequency.
ERROR MESSAGES TEMP OVER
MEANING q The temperature is too high. (Turn off the power, and wait for a while.)
TOC FORM (**)
q There is an error in the recording signal. (Erase all of the tracks, and then record again.)
TOC FULL
PLAY MD PROTECTED
q You tried to record on a playback-only disc. q The write protection tab of a MiniDisc is set to the protected position. q You tried to record on a playback-only disc. Tr. Protect
q There is no space left for recording character information (track names, disc names, etc.). q The track has been protected from being erased. (Edit the track with the device on which it was recorded.)
SORRY
q Since a track number is currently being located or updated, the unit cannot accept your command. (Wait for a while and try the operation again.)
? DISC
q A disc which contains data other than music was played. (A disc which contains nonmusic data cannot be played.) q There is an error in the signal recorded on the disc.
Number or symbol appears in (*) position.
�6�
|
|
|
> |
|
